ADIPRENE BLM 500. Reactive Prepolymer PRODUCT DATA. Urethane Prepolymers
|
|
- Cynthia Underwood
- 6 years ago
- Views:
Transcription
1 PRODUCT DATA ADIPRENE BLM 500 Water Emulsifiable/Dispersible Reactive Prepolymer ADIPRENE BLM 500 ADIPRENE BLM 500 is an MDI based urethane prepolymer with blocked isocyanate curing sites, which can be activated by heating. The blocked curing sites allow protracted storage of the polymer in the presence of moisture and active vulcanizing agents. Diamine-cured ADIPRENE BLM 500 yields vulcanizates having improved performance over common TDI based urethane materials. MDI is one of the most commonly used diisocyanates in industrial polyurethane applications. However, blocked MDI prepolymer and its application are very limited. Conventional MDI prepolymers generally contain more than 10% free MDI, due to the need of using excess amount of the diisocyanate in prepolymer preparation. Blocked prepolymers are highly viscous and gel-like in appearance. This is from the high tendency of crystallization of the blocked MDI. Urethane Prepolymers ADIPRENE BLM 500 is a novel blocked system based on low free isocyanate technology. With Chemtura s unique process, the residual MDI in the unblocked preoplymer is below 0.5%. The resulting blocked prepolymer has very good processing characteristics, such as low viscosity and melting point. Moreover, the widely used curative for conventional MDI prepolymer is 1,4 butanediol (BDO). Amine cured MDI polyurethanes are preferred for many demanding applications, expecially those requiring toughness and modulus retention at high temperature. Thus, blocked MDI prepolymers open to the opportunity to use amine curatives, for end-use properties not achieved by conventional MDI urethanes. Materials made from ADIPRENE BLM 500 have high tensile strength and high elongation, and especially have excellent tear strength. They are also low in viscous damping indicating low heat generation and more durability in dynamic applications. ADIPRENE BLM 500 is well suited as a vehicle for abrasion resistant coatings for fabric and rubber, and for solvent-resistant adhesives.
2 POLYMER PROPERTIES TABLE I Typical Properties of ADIPRENE BLM 500 Prepolymer Physical form... Viscous liquid Color... Light yellow to amber Isocyanate content, % Blocked Free max. Specific Gravity at 77 F (25 C) F (40 C) Viscosity (Brookfield), cps (Pa 122 F (50 C)... 12,000 35,000 (12 35) Raw prepolymer storage stability... Excellent at room temperature. ADIPRENE BLM 500 tends to freeze slowly when stored at 75 F (24 C) or below. It is unharmed by freezing and may be thawed by storing overnight at 125 F (52 C). After thawing, the liquid should be thoroughly mixed before it is used. Solubility... Soluble in most common solvents such as toluene, ethyl acetate, methyl ethyl ketone, and trichloroethylene. Solubility is limited in aliphatic solvents and alcohols. Handling Precautions... During heat cure, the blocking agent (methyl ethyl ketoxime), a volatile flammable liquid (b.p. above 302 F [150 C]), is evolved and provisions must be made for removal of this vapor. Trace amounts of diphenylmethane diisocyanate may also be released during cure. The blocking agent and diphenyl methane diisocyanate are irritants and harmful; exposure to and inhalation of their vapors should be avoided. Note: These data are presented to describe ADIPRENE BLM 500 and are not intended to serve as specifications. 2
3 TYPICAL VULCANIZATE PROPERTIES VULCANIZATE PROPERTIES Cured films of ADIPRENE BLM 500 urethane rubber are tough, highly extensible and have a high modulus. Table II shows the comparison of amine cured Adiprene BLM 500 and BL 16 (a TDI based prepolymer), and BDO cured conventional MDI prepolymer. Using Lonzacure MDEA and MDA, cured BLM 500 is tougher than BL 16/MDA, and much tougher than conventional MDI prepolymer/bdo, in terms of higher hardness, modulus and tear strength. Material from de-blocked/cured BLM 500 prepolymer also provides improved dynamic performance. Figure 1 demonstrates much lower damping at both low and high temperatures of material obtained with Adiprene BLM 500 (MDI based) vs. Adiprene BL 16 (TDI based.). TABLE II Property Comparison of Chain Extended BLM 500 vs. BL 16 and conventional MDI. B635* BLM 500 BL 16 Curative BDO ** MDEA *** MDA **** MDA Hardness, Shore A % Modulus, psi % Modulus, psi Tensile, psi Elongation at break, % Split Tear, pli * Vibrathane B 635 is a conventional non blocked MDI/PTMEG prepolymer. ** 1,4 Butanediol. *** 4,4 methylene-bis-2,6 diehylaniline **** 4,4 methylene dianiline Figure 1. BLM-500 vs BL-16; Damping Property Comparison BLM-500/MDA BL-16/MDA Tan Delta Temperature, C 3
4 COMPOUNDING CURING SYSTEMS When unblocked by heat, the regenerated NCO groups in ADIPRENE BLM 500 react with any of the materials (containing active hydrogens) normally used as isocyanate reactants. Thus polyols and polyamines can be used as curatives. Polyols are quite slow in reacting with this prepolymer, so the most useful curatives appear to be aromatic diamines such as 4,4 methylene dianiline, and 4,4 methylene-bis-2,6 diethyl aniline. ADIPRENE BLM 500 is unblocked by heating at 212 to 266 F ( C) for a period of time depending upon film thickness; a ten-mil (0.25mm) film of freshly mixed prepolymer and MDA is fully cured after one hour at 266 F (130 C). Aged blends will cure somewhat faster. Vulcanization of ADIPRENE BLM 500 in sections thicker than about 20 mils (0.50 mm) is impractical because of the difficulty of removing the blocking agent from thick films without blowing and subsequent porosity. COMPOUNDING Coatings and adhesives can be prepared in a wide viscosity range by diluting ADIPRENE BLM 500 with such solvents as toluene, xylene, ethyl acetate, or propylene glycol monomethyl ether acetate. Table III shows the viscosity/solvent level relationship of a blend of ADIPRENE BLM 500 and propylene glycol monomethyl ether acetate (PMA). TABLE III Viscosity of Solvent Solutions of ADIPRENE BLM 500 ADIPRENE BLM 500, 100 parts by weight Propylene glycol monomethyl ether acetate, phr Viscosity at 104 F (40 C), cps (Pa s) ,000 (70) ,000 (3.0) (0.65) (0.25) A typical solvent-diluted composition is shown in Table IV. This composition can be prepared as follows: mix ADIPRENE BLM 500 and propylene glycol monomethyl ether acetate at 104 F (40 C); melt the MDA at 212 F (100 C) and add to the ADIRENE BLM 500 solution with continuous stirring. MDA may also be added as a solution in solvent. 4
5 SOLVENT INFORMATION TABLE IV Solvent Diluted Composition Parts by weight: ADIPRENE BLM PMA (Propylene Glycol Monomethyl Ether Acetate) Methylene dianiline A substrate having a ten-mil (0.25mm) coating of the formulation in Table IV was heated at 158 F (70 C) for minutes to drive off the solvent, followed by one hour at 266 F (130 C) to cure the prepolymer. Properties of this cured coating are listed in Table II. Higher temperature, for example 302 F (150 C), may shorten the time to cure the prepolymer. Pigmented coatings can readily be prepared with ADIPRENE BLM 500. Solventless mixtures of ADIPRENE BLM 500 and MDA can be prepared by melting the MDA at 212 F (100 C) and adding it with continuous agitation to ADIPRENE BLM 500 which has been warmed to about 158 F (70 C). a Viscosity vs. temperature of ADIPRENE BLM 500 is given in Table V. Storage life will be reduced if ADIPRENE BLM 500 is heated above 176 F (80 C). It may be necessary to heat solventless blends during application to achieve a workable viscosity. A blend of ADIPRENE BLM 500 and 10 phr MDA will remain fluid at 158 F (70 C) for more than one hour. ADIPRENE BLM 500 should also be considered in adhesive applications. The ability to be applied without solvents is a desirable feature in such applications. The cured film has a high degree of resistance to dry cleaning solvents and provides a flexible bond to fabric-to-fabric and flock bonding applications. Temperature, F ( C) TABLE V Viscosity of Adiprene BLM 500 Viscosity 122 (50) cps 140 (60) 6700 cps 158 (70) 510 cps a If the ADIPRENE BLM 500 or the agitator is not warm, molten MDA will crystallize before going into solution. The resulting crystals will dissolve at an extremely slow rate. 5 REV: 12/04dd:7/05dd
MDI Prepolymers Extended With Amines A Reality!
customized polyurethanes MDI Prepolymers Extended With Amines A Reality! Dr. Ashok M. Sarpeshkar Overview Baytec MAC prepolymer product line Effect of free-monomer on properties Curing with MbOCA Curing
More informationCompounding With Viton Curative Masterbatches
Technical Information Compounding With Viton Curative Masterbatches Introduction The bisphenol cure system provides a unique combination of excellent processing safety and fast cure rates, together with
More information(51) Int Cl.: D01F 6/70 ( ) D01D 5/04 ( )
(19) TEPZZ 66Z 7 A T (11) EP 2 660 373 A2 (12) EUROPEAN PATENT APPLICATION published in accordance with Art. 13(4) EPC (43) Date of publication: 06.11.13 Bulletin 13/4 (21) Application number: 1182801.7
More informationEffect of Reaction Time on the Synthesis and Properties of Isocyanate Terminated Polyurethane Prepolymer
Effect of Reaction Time on the Synthesis and Properties of Isocyanate Terminated Polyurethane Prepolymer Runumi Gogoi 1*, M. Sarwar Alam 2 and Rakesh Kumar Khandal 3 1 Material Science Division, Shriram
More informationEpolene Polymers as Petroleum Wax Modifiers
Westlake Chemical 50 Year Anniversary Epolene Polymers Epolene Polymers as Petroleum Wax Modifiers A majority of petroleum wax production is consumed by the paper and packaging industry while the rest
More informationWhat is Paint?
What is Paint? 2017 1 PAINT IS A LIQUID DESIGNED FOR APPLICATION TO A SURFACE IN A THIN FILM THAT CURES TO AN SOLID FILM. A COATING WHICH PROTECTS THE SURFACE OF AN OBJECT. USED TO CREATE DESIRED AESTHETICS
More informationWhat Made This Part Fail?
What Made This Part Fail? Richard Palinkas Chemtura Corporation Ride Wheel With Internal Cracks Cracks appeared when the wheel was machined on a lathe. They were not visible on the surface. They were primarily
More informationSuper Shield TM Water Based Silver Coated Copper Conductive Coating
Description The 843WB Super Shield TM is a one-part urethane system pigmented with highly conductive silver coated copper flake. It is easy to use, with no let-down, and no heat cure necessary. It can
More informationNeuthane Prepolymers & Systems: Examples of Proven Applications
Neuthane Prepolymers & Systems: Examples of Proven Applications Contact for India Market: Sanjay CHOUBEY, M.Eng (Polymer) Polymer Technology Group *Systems * Solutions* Raw Materials Office: Technology
More informationCHEMICAL RESISTANT EPOXY
CHEMICAL RESISTANT EPOXY DATE - 19 DECEMBRER 2016 TECHNICAL DATA SHEET DESCRIPTION is a solvent-less, two component epoxy coating system. It exhibits very good appearance and chemical and physical properties.
More informationNX 795 Enhancing latex products
NX 795 coalescing agent for latex products Promotes uniform film formation with optimal properties Universal in all latex systems Easy to incorporate Reduces minimum film-formation temperature Non-VOC
More informationContents. NIIR Project Consultancy Services (NPCS) 1/6
The Complete Book on Resins (Alkyd, Amino, Phenolic, Polyurethane, Epoxy, Silicone, Acrylic), Paints, Varnishes, Pigments & Additives (Surface Coating Products with Formulae)(3rd Revised Edition) Author:
More informationVia Carolina Romani 1/11 I Bresso (MI) Italy Tel Fax
Italian Polyurethane Manufacturer Via Carolina Romani 1/11 I-20091 Bresso (MI) Italy Tel. 0039+02+6103166 Fax 0039+02+6105708 E-mail: sintochem@sintochem.it Web-site: www.sintochem.com The company SINTOCHEM
More informationSuper Shield TM Water Based Silver Conductive Coating 842WB Technical Data Sheet 842WB-Liquid
Description Super Shield TM The 842WB Super Shield TM is a one-part urethane system pigmented with highly conductive silver flake. It is easy to use, with no let-down, and no heat cure necessary. It can
More informationMold Release, Break-In, Maintenance and Storage. Linda Bergstrom
Mold Release, Break-In, Maintenance and Storage Linda Bergstrom Mold Release Requirements Form a barrier between the mold and molded part Provide a lubricating film which allows the molded part to be easily
More informationOffset Inks - Basics
Offset Inks - Basics Lithographic inks are paste inks, The press works the ink, thereby heating it and reducing its viscosity or body, making it flow readily to provide a uniform ink film to the image
More informationMATERIAL AND EQUIPMENT STANDARD FOR EPOXY POLYAMIDE PAINT AS INTERMEDIATE PAINT ORIGINAL EDITION MAY 1993
MATERIAL AND EQUIPMENT STANDARD FOR EPOXY POLYAMIDE PAINT AS INTERMEDIATE PAINT ORIGINAL EDITION MAY 1993 This standard specification is reviewed and updated by the relevant technical committee on Nov.
More informationTechnical Product Information
O.D. Thermochromic Function: Irreversible Product Name: Kromagen Black K60-NH Last Revision: 11/02/2015 Technical Product Information Kromagen Black K60-NH can be supplied as a Concentrate, Water Based
More information1. Initial Precautions 2. Technical Precautions and Suggestions 3. General Information and Cure Stages 4. Understanding and Controlling Cure Time
How to apply Arctic Silver Premium Thermal Adhesive 1. Initial Precautions 2. Technical Precautions and Suggestions 3. General Information and Cure Stages 4. Understanding and Controlling Cure Time 5.
More informationCHEMICAL RESISTANT EPOXY
CHEMICAL RESISTANT EPOXY ADHL-EPOX-CHEM TECHNICAL DATA SHEET DESCRIPTION ADHL-EPOX-CHEM is a solvent-less, two component epoxy coating system. It exhibits very good appearance and chemical and physical
More informationManufacture of Cast Products
Manufacture of Cast Products When a layer of rubber is deposited on the interior surface of a hollow mould, it is known as casting. The latex products obtained by the casting process are hollow and toys,
More informationProduction and Study of Factors Affecting the Flexibility of Polyester Paint Using Local Materials
ISSN: 2276-7835 Impact Factor 2012 (UJRI): 0.7563 ICV 2012: 5.62 Production and Study of Factors Affecting the Flexibility of Polyester Paint Using Local Materials By Dr. Opara C.C. Sokore Bekere Ugwo
More informationBreathable Reactive Hot Melt Adhesives for Textile Lamination. Lee Polance Product Director RISE 2013, Denver, CO Oct 2, 2013
Breathable Reactive Hot Melt Adhesives for Textile Lamination Lee Polance Product Director RISE 2013, Denver, CO Oct 2, 2013 H.B. Fuller Company A leading global provider for adhesives and sealants with
More informationMATERIAL AND EQUIPMENT STANDARD FOR VINYL PAINT (ALUMINUM) AS INTERMEDIATE AND TOP COAT (FINISH) ORIGINAL EDITION MAY 1993
MATERIAL AND EQUIPMENT STANDARD FOR VINYL PAINT (ALUMINUM) AS INTERMEDIATE AND TOP COAT (FINISH) ORIGINAL EDITION MAY 1993 This standard specification is reviewed and updated by the relevant technical
More informationLascaux Synthetic Resins and Varnishes
Lascaux Synthetic Resins and Varnishes Acrylic Resin P 550 (Plexisol) 40% gloss Organic solution of an acrylic resin based on butyl methacrylate Tg 25 C. pure, soft, thermoplastic acrylic resin lightproof
More informationAdhesives. Note. 6.2 Hanex Adhesive 6.2-a Types and Applications
6.2 Hanex Adhesive 6.2-a Types and Applications There are many companies that specialize in manufacturing Solid Surface Adhesive products. These companies have a comprehensive line of colors and selections
More informationMATERIAL AND EQUIPMENT STANDARD FOR CHLORINATED RUBBER INHIBITIVE PRIMER ORIGINAL EDITION NOV. 1993
MATERIAL AND EQUIPMENT STANDARD FOR CHLORINATED RUBBER INHIBITIVE PRIMER ORIGINAL EDITION NOV. 1993 This standard specification is reviewed and updated by the relevant technical committee on Jan. 1999.
More informationEffects of Post-Processing Treatments on the Image Stability of Color Prints
TECHNICAL DATA / REFERENCE February 2004 E-176 Effects of Post-Processing Treatments on the Image Stability of Color Prints For many years, Kodak has been investigating the factors that affect the image
More informationNew Product Update & Parts Information
Update & Parts NEW Range Liquid Accessories Range Vapormatic is pleased to introduce a new liquid accessories range to replace existing s. The NEW range is manufactured in the UK, to ISO 9001 standard.
More informationSOLVENTS & RETARDERS STANDARD BUTYL CARBITOL PROPYLENE GLYCOL BUTYL CELLOSOLVE VINYL WASH THINNER N-116 XYLOL INK DEGRADIENT HO 1000 VARSOL
SOLVENTS & RETARDERS BUTYL CARBITOL A slow evaporating solvent used in diluting certain nylon inks. PROPYLENE GLYCOL An effective flow agent for water phase paints. It also retards the drying time. BUTYL
More informationAdvanced Troubleshooting of Polyurethane Elastomers. By Nick Skirkanich. Sales Development Manager, COIM USA Inc.
Advanced Troubleshooting of Polyurethane Elastomers By Nick Skirkanich Sales Development Manager, COIM USA Inc. Troubleshoo*ng Main Categories Raw Material Issues Processing Problems Appearance Problems
More informationTechnical Data Sheet : Product Identification:
Tirupati Inks Limited An ISO 9001:2008 & ISO 14001:2004 Company REF No.: TDS/007 Rev. Date: 25/03/13 Issue Date: 25/03/13 Page No.: 1 to 5 Version No. 02 Technical Data Sheet : Product Identification:
More informationAquaCLAD Water-Reducible Rust Preventative Alkyd
AquaCLAD 1600 Water-Reducible Rust Preventative Alkyd A rust preventative coating for interior and exterior steel in mild to moderate industrial environment. Recommended For Features Refinish Market High
More informationAn Approach to Alternative Adhesives. Greg Montello, Product Chemistry Manager
An Approach to Alternative Adhesives Greg Montello, Product Chemistry Manager History of adhesive alternatives In 1995, New Balance began moving away from using solvent-based adhesives to attach uppers,
More informationTotal Ground TM Carbon Conductive Coating 838AR Technical Data Sheet 838AR-Liquid
Description The 838AR Total Ground TM is a one-part durable acrylic lacquer pigmented with a highly conductive carbon powder. It utilizes a solvent based system with no heat cure necessary. The cured coating
More informationCold curing adhesive K-X280
Instructions for use English Cold curing adhesive K-X280 A4048-1.0 en English 1 Safety instructions... 3 2 General information... 3 2.1 Scope of delivery for K-X280... 3 2.2 Accessories required for installation...
More informationOf the three grades, grade 1 tallow was chosen as the starting material as it appears the most homogenous and the lightest in colour.
Fuel supplement Studies (Tallow) The limited quantity of fossil fuels has been the primary driving force for research into alternative sources of fuel. Natural materials have always provided Man with combustible
More informationDESCRIPTION/APPLICATION HK RESEARCH GEL COATS DESCRIPTION
Product Data 908 LENOIR ROAD POST OFFICE BOX 1809 HICKORY, NORTH CAROLINA 28603-1809 TELEPHONE (828) 328-1721 TOLL FREE (800) 334-5975 FAX (828) 328-4572 DESCRIPTION/APPLICATION HK RESEARCH GEL COATS DESCRIPTION
More informationDuPont Plas-Stick 2332S Low VOC Adhesion Promoter
Description Plas-Stick 2332S is a Low VOC gray pigmented adhesion promoter for polyolefin or non-polyolefin unprimed automotive plastics. When combined with proper surface preparation, this product enhances
More informationNew Technologies for Clear Air Care Applications
New Technologies for Clear Air Care Applications 1 Topics Definitions Progression of Technology How Gels are Formed Properties of Modified Polyamide Gellants Performance in Container Candles and Pillar
More information13 Congresso Internacional de Tintas 13ª Exposição Internacional de Fornecedores para Tintas
HIGH PERFORMANCE ADDITIVES FOR WATER BASED AND LOW VOC PAINTS AND COATINGS Daniel de Moura Massarente, Wolfgang Geuking Croda Coatings and Polymers The replacement of solvent-based coatings by water based
More informationFinishes and Finishing Techniques
Finishes and Finishing Techniques TED 126 Spring 2007 Review pages 147-150, 284-294 Finishes and finishing techniques The finishing process to choose depends partly on the type of wood and the appearance
More informationMasking: Each mirrored sheet is well protected by a durable paint backing and
STORAGE Horizontal storage: If mirror sheets are stored flat, care must be taken to avoid warping, slipping and scratching. If different sizes are stored together the largest panels should at the bottom
More informationPolyisocyanates and Prepolymers
Polyisocyanates and Prepolymers Covestro Deutschland AG Business Unit Coatings, Adhesives and Specialties D-51365 Leverkusen Germany www.coatings.covestro.com cas-info@covestro.com This information and
More informationFEVE Fluoropolymer Emulsions for Performance Improvement in Architectural Coatings
FEVE Fluoropolymer Emulsions for Performance Improvement in Architectural Coatings Bob Parker, Applications Chemist SSCT Annual Meeting Sept. 26 Sept. 29, 2010 Outline Overview of FEVE resin technology
More informationDorus Specification Sheets. Presented by
Dorus Specification Sheets Presented by Version 1.1 - July 20, 2000 Dorus Adhesives Application Techniques Woodtape offers the complete Dorus line of Hot Melt adhesives for automatic edgebanding applications.
More informationBEST PRACTICES REPORT DECORATIVE LIGHT POLE PROTECTION. Parks & Recreation Dept. City of Sioux Falls, SD PROJECT OVERVIEW:
After NCI Parks & Recreation Dept. City of Sioux Falls, SD Industrial Customer: City of Sioux Falls Parks & Recreation Project: Fortify oxidized paint on a park decorative light pole that was beginning
More informationPaints and varnishes Corrosion protection of steel structures by protective paint systems. Part 5: Protective paint systems
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 12944-5 Third edition 2018-02 Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 5: Protective paint
More informationBulldog Adhesion Promoter System
PABC124 Abrasive Cleaner GTPO123, QTPO123 Adhesion Promoter (liquid) ETPO123B Adhesion Promoter (aerosol) Bulldog Adhesion Promoter is the premier adhesion promoter for the auto body collision repair market.
More informationUNIT REF: PO13K UNIT TITLE: KNOWLEDGE OF VEHICLE COLOUR MATCHING
UNIT REF: PO13K UNIT TITLE: KNOWLEDGE OF VEHICLE COLOUR MATCHING Level: 3 Route: Knowledge Credit Value: 6 GLH: 45 Mapping: This unit is mapped to the IMI NOS PO13 Rationale: This unit enables the learner
More informationSkype: baliprefabworld Tel.: ABSTRACT
ABSTRACT Coating prior to assembly is not an option for us, since this will disguise the type of wood used so that - during an inspection - a customer is unable to verify what type of hardwood is used.
More informationFOCUS TECHNOLOGY THE BEAUTY OF A LACQUERED SURFACE
FOCUS TECHNOLOGY FOCUS TECHNOLOGY THE BEAUTY OF A LACQUERED SURFACE Snaidero is one of the few companies on the market with more than 50 years experience in the development of lacquered kitchens. Its product
More informationDescription. Product Line. Packaging. Storage. Instruction Bulletin 3.12 (UK)
Instruction Bulletin 3.12 (UK) Release (UK-B) July 2000 Screen Printing with 3M Screen Printing Ink Series 1900 (Line Inks) Description The 3M Screen Printing Ink Series 1900 are used on 3M Controltac
More informationBEST PRACTICES REPORT. Parks & Recreation Dept. City of Sioux Falls, SD PROJECT OVERVIEW: Industrial Customer: City of Sioux Falls Parks & Recreation
NANO-CLEAR INDUSTRIAL COATING FOR WATER OXIDIZED FEATURE WATER PROTECTION FEATURE Parks & Recreation Dept. City of Sioux Falls, SD Industrial Customer: City of Sioux Falls Parks & Recreation Project: Fortify
More informationATELIER MEDIUMS. Interactive Mediums
ATELIER MEDIUMS Atelier Interactive is very simple to use: use with our traditional acrylic mediums (or water) for traditional overpainting and layering techniques. Use with our exclusive interactive mediums
More informationCrackle Paste is a water-based product formulated with styrene-acrylic copolymer emulsions, and may have a tendency to yellow.
PRODUCT DESCRIPTION Crackle Paste is a water-based product formulated with styrene-acrylic copolymer emulsions, and may have a tendency to yellow. This product has white, low-density solids that replace
More informationVolume Solids %
Product Name Full Product Name Type of Product Description 2K acrylic urethane solid topcoat Concept is a 2 K Solid tinting system. It incorporates a large range of colour formulations, with high opacity
More informationHERNON MANUFACTURING, INC.
SAG1:0517_2.1 For many years, some of the world s leading manufacturers of loudspeakers and speaker components have relied on HERNON MANUFACTURING, INC. s superior quality adhesives and precision dispensing
More informationGRIP-GARD BC Translucent For Professional Use Only
Description Grip-Gard BC uses a specially blended binder which converts Grip-Gard BC toners into a fast drying, durable backlit sign coating. With this system, backlit plastic signs can be painted quickly
More informationADDITIVES FOR PAD PRINTING
ADDITIVES FOR PAD PRINTING Due to the diversity of the pad printing process it is impossible to deliver such inks in ready-to-print adjustments. Therefore use of various additives to adjust the pad printing
More informationTECHNICAL INFORMATION CLEAR CONCENTRATED INDUSTRIAL VARNISH BARNIZ INDUSTRIAL CONCENTRADO TRANSPARENTE
DESCRIPTION is a single part, solvent-base wood finish, developed from alkyd resins. Fast Drying, beautiful shine and good leveling. USE Industrial and domestic use. Only for wood surfaces that will stay
More informationBC Translucent uses a specially
Grip-Gard BC Translucent Description Technical Data Sheet October 2013 Topcoat Grip-Garinto a fast drying, durable backlit sign coating. With this system, backlit plastic signs can be painted BC Translucent
More informationTroubleshooting Guide. Solutions to Common Finishing Problems
Troubleshooting Guide s to Common Finishing s 1 Contents Adhesion Intercoat Stain Substrate Air Entrapment / Pinholing Bénard Cells Bleeding Blisters / Pinholes Blocking Blooming Blushing Brittleness Brown
More informationACRYLITE extruded sheet (FF)
Placeholder product brand Technical information ACRYLITE extruded sheet (FF) #9 Painting and Printing This brief gives advice for: Equipment and Materials Procedures Trouble Shooting Equipment and Materials
More informationSuper Shield TM Silver Conductive Coating 842AR Technical Data Sheet
Description The 842AR Super Shield TM is a one-part durable acrylic lacquer pigmented with an extremely conductive silver flake. It utilizes a solvent based system with no heat cure necessary. The cured
More informationDuPont Pyralux AP All-Polyimide Flexible Laminate A Family of High-Performance Adhesiveless Laminates for Flexible Printed Circuit Applications
Technical Information DuPont Pyralux AP All-Polyimide Flexible Laminate A Family of High-Performance Adhesiveless Laminates for Flexible Printed Circuit Applications Product Description Pyralux AP double-sided,
More informationNOTE: This product can be used externally if UV Guard is added (BY REQUEST ONLY).
Product Description PHOENIX PAINTS MAXICOAT 100 is a 2 Pack Water-Dispersed Top Coat which not only exhibits the physical and chemical strengths of epoxy, but also the safety and convenience of water as
More informationThe Basics of Flexible Packaging Printing Flexography Rotogravure
The Basics of Flexible Packaging Printing Flexography Rotogravure Presented by: Warren E. Durling Associate Research Fellow Clorox Services Company / Glad Division Slide 2 Design to Substrate Ink Management
More informationAtelier Mediums. They are set out in a progression from a thick heavy bodied gel through to a very liquid medium.
Atelier There are several top quality brands of artist acrylic on the world market, but Atelier Interactive is the only brand that can be used in a Fast Drying Mode and in a Wet Blending Mode. There are
More informationFLEXOGRAPHIC PRINTING PRINTING ON PACKAGING TAPES
FLEXOGRAPHIC PRINTING PRINTING ON PACKAGING TAPES ICHEMCO - YOUR PARTNER FOR FLEXO-PRINTING As soon as the first PP tapes have been introduced in the market, ICHEMCO started to develop new dedicated systems
More informationML² Multi Layer Micro Lab
Deliverable 4.5 ML² Multi Layer Micro Lab D4.5 - Report on product range for UV curing lacquers, validated for ML² devices 1. Introduction... 2 2. UV embossing lacquer chemistry... 2 2.1. The main components
More informationMetal 3in1. Applied directly to rust A smooth gloss anti-rust enamel paint for metal surfaces
Applied directly to rust A smooth gloss anti-rust enamel paint for metal surfaces It prevents humidity from penetrating, providing long-lasting rust protection Highly resistant to ultraviolet radiation,
More informationVIJAY CHEMSOL R.S.No.110/5, HM Road, Industrial area, Sedharapet, Pondicherry INDIA
VIJAY CHEMSOL R.S.No.110/5, HM Road, Industrial area, Sedharapet, Pondicherry-605 111. INDIA ABOUT US: VIJAY CHEMSOL is based at Pondicherry, INDIA and having the manufacturing unit in Sedharapet industrial
More informationThe system is also approved by KOMO (Netherlands) and FCBA (France) as adhesive Type I.
Technical Data Sheet Use is always used with hardener Prefere 6651 and is as such a two-component adhesive system based on an emulsion polymer and an isocyanate (EPI-adhesive) used in the manufacture of
More informationGels, Pastes, Liquid Mediums & Additives
Gels, Pastes, Liquid Mediums & Additives There are far more acrylic mediums available than you may ever want to explore. It can get somewhat confusing. So, I will try to simplify it as much as possible,
More informationHELIOS RESINS, HIGH-QUALITY RESINS FOR RELIABLE COATING SOLUTIONS. METAL RESINS SUPPLIER SINCE GOLDEN RESINS DEVELOPED BY ADVANCED TECHNOLOGY
METAL HELIOS S, HIGH-QUALITY S SUPPLIER SINCE 1908. METAL These resins ensure excellent protection coatings for a broad range of industrial metal coating applications. S FOR RELIABLE COATING SOLUTIONS.
More informationAutomotive Refinish Terminology
Automotive Refinish Terminology Accelerator: A substance that when added to a paint will speed up the rate of cure. Acetone: A very fast evaporating solvent with high solvency for certain types of compounds
More informationPOTTING & ENCAPSULATING
[ Table of Contents ] 105 EPOXIES & POLYURETHANES 107 SILICONES 111 SILICONE EQUIPMENT 113 HOT MELTS 114 HOT MELTS EQUIPMENT 115 Potting and encapsulating compounds are used to provide mechanical reinforcement
More informationThe Most Beautiful, Longest-Lasting, High Gloss Shine for Brightwork VARNISH
The Most Beautiful, Longest-Lasting, High Gloss Shine for Brightwork VARNISH P R O D U C T S A N D A P P L I C A T I O N S Exquisitely varnished wood is the reflection of the most beautifully maintained
More informationBright Precious Metal Preparations for the Production of Decals for Glass
Bright Precious Metal Preparations for the Production of Decals for Glass 1 General Information Heraeus supplies bright gold and bright platinum pastes for the production of decals for glass with a precious
More informationFull Product Name. Products. Properties. 2K Etch Primer. Type of Product Description
Product Name Full Product Name Type of Product Description 2K acid etch primer Concept is an acid containing etch and primer in one product. This Product is characterized by excellent adhesion and corrosion
More informationAtelier Mediums. NEW Atelier Mediums All Have A Double Function
Atelier We have divided our mediums into two sections. The established old mediums are familiar to Atelier Interactive users, and most of them are traditional in behaviour and convert the paint mixed with
More informationSAN7>--9S-OaI 7 L 34NO? 8 - b2 I-) c.
SAN7>--9S-OaI 7 L 34NO? 8 - b2 I-) c. SAFE EPOXY ENCAPSULANT FOR HIGH Robert 0. Sanchez (505)844-3103 FAX (505)844-3888 E-Mail rosanch@sandia.gov 0 Wendal E. Archer (505)844-6618 FAX (505)844-3888 E-Mail
More informationRAKU-TOOL. Liquid Products. Casting, Laminating, Gelcoat and Multipurpose Resins. Our systems for your applications. discover the future
Liquid Products Casting, Laminating, Gelcoat and Multipurpose Resins. Our for your applications. discover the future Product Overview/2 Component Liquid Systems Resin (ISO 113) RAKU-TOOL Gelcoat Systems
More informationDuPont Plas-Stick 2330S and A-2330S Plastics Adhesion Promoter
Description Plas-Stick 2330S is a green-gray pigmented adhesion promoter for polyolefin or non-polyolefin unprimed automotive plastics. When combined with proper surface preparation, this product enhances
More informationP A I N T I N G S Y S T E M. This specification has been divided into 05 chapters designated as under :
RDSO SPECIFICATION NO. M&C/PCN/100/2006 SPECIFICATION FOR POLYURETHANE PAINTING SYSTEM (TWO PACK) FOR THE EXTERIOR PAINTING OF RAILWAY COACHES DIESEL AND ELECTRIC LOCOMOTIVES AND OTHER INDUSRIAL APPLICATIONS
More informationSection 914. JOINT AND WATERPROOFING MATERIALS
914.01 Section 914. JOINT AND WATERPROOFING MATERIALS 914.01. General Requirements. Joint and waterproofing material for use in concrete construction must meet the requirements of this section. 914.02.
More informationBig Sky Product Information Sheet. Epoxy Prime Primer/Sealer PS3042 (Lt. Gray) PS3044 (Dk. Gray) PS3045 (Black) PS3047 (Yellow Oxide)
Big Sky Product Information Sheet TECHNICAL SUPPORT ((800) 328-4892 P.I. Sheet #3008 Epoxy Prime Primer/Sealer PS3042 (Lt. Gray) PS3044 (Dk. Gray) PS3045 (Black) PS3047 (Yellow Oxide) READ ENTIRE PRODUCT
More informationTimber Floors & Floor Finishes
Timber Floors & Floor Finishes Australian Timber Flooring Association ABN 16 524 524 226 11 Oleander Avenue Shelley Beach Qld 4551 Email flierman@ozemail.com.au 1.0 INTRODUCTION This data sheet outlines
More informationPRINTING TECHNOLOGY & INNOVATION DAYS FOR FLEXIBLE PACKAGING. Rajkot, Gujarat, India 19/20 September 2018
PRINTING TECHNOLOGY & INNOVATION DAYS FOR FLEXIBLE PACKAGING Rajkot, Gujarat, India 19/20 September 2018 0 PRINTING TECHNOLOGY & INNOVATION DAYS FOR FLEXIBLE PACKAGING HOSTED BY: 1 PRINTING TECHNOLOGY
More information10P20-44MNF High Solids Epoxy Primer
Technical Data Sheet Product Group High solids epoxy primer Characteristics Product Information A high solids urethane compatible, Skydrol resistant primer for application to aircraft exterior surfaces.
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 12944-5 Second edition 2007-09-15 Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 5: Protective paint systems Peintures et vernis
More informationMaking a Surface Coating Kersti Cox, Miami University, Oxford, OH
Making a Surface Coating Kersti Cox, Miami University, Oxford, OH To close the yellow note, click once to select it and then click the box in the upper left corner. To open the note, double click (Mac
More informationPrinting & Packaging resins, performance and formulation additives selection guide for packaging solutions
Printing & Packaging resins, performance and formulation additives selection guide for packaging solutions 2 Printing & Packaging resins and additives Supporting the conversion to sustainable solutions
More informationPaper Ink Preparation by Three Roll Mill
Paper Ink Preparation by Three Roll Mill 1. INTRODUCTION Printing of one form or another has been with us for centuries and whilst the technologies of both the printing process and the ink formulations
More informationAtelier Mediums. NEW Atelier Mediums. New! Heavy Gel (Satin)
Atelier There are several top quality brands of artist acrylic on the world market, but Atelier Interactive is the only brand that can be used in a Fast Drying Mode and in a Wet Blending Mode. There are
More informationMETAL, TRANSPORT AND ACE
METAL, TRANSPORT AND ACE HELIOS S, HIGH-QUALITY S SUPPLIER SINCE 1908. METAL, TRANSPORT AND ACE THESE S ENSURE EXCELLENT PROTECTION COATINGS FOR A BROAD RANGE OF INDUSTRIAL METAL COATING S. S FOR RELIABLE
More informationThese Application Instructions cover surface preparation, application equipment and application details for HEMPADUR MASTIC 45880/45881.
For product description refer to product data sheet HEMPADUR MASTIC 45880/ HEMPADUR MASTIC 45880/ High temperatures: 45881: BASE 45889 with CURING AGENT 95881 Low to medium temperatures: 45880: BASE 45889
More informationUse suitable respiratory protection Akzo Nobel Sign Refinishes recommends the use of a fresh air supply respirator.
Description A two-component high solids, low VOC, HAPs free epoxy primer. Grip-Gard Epoxy Sealers White and Gray are fast drying primers with excellent corrosion protection over multiple substrates. The
More informationStyroSpray 1000 Product Description
StyroSpray 1000 Product Description StyroSpray 1000 is a two component, rigid, 100% solids (contains no V.O.C.), polyurethane polyurea hard coating for EPS foams. It is recommended for hard shell coating
More information