GB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD OF THE
|
|
- Britney Eaton
- 5 years ago
- Views:
Transcription
1 Translated English of Chinese Standard: GB/T GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS J 13 GB/T Replacing GB/T Hexagon Head Bolts 六角头螺栓 (ISO 4014:2011, Hexagon Head Bolts Product Grades A and B, MOD) Issued on: February 24, 2016 Implemented on: June 1, 2016 Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the People's Republic of China. Page 1 of 18
2 Table of Contents Foreword Scope Normative References Dimensions Specifications and Reference Standards Designation Page 2 of 18
3 Foreword This Standard belongs to a national standards series Hexagon Nuts (Part). The series comprises the following: -- GB/T 27 Hexagon Fit Shank Bolts -- GB/T 28 Hexagon Fit Shank Bolts with Split Pin Hole on Shank -- GB/T 29.1 Hexagon Bolts with Slot on Head -- GB/T 29.2 Hexagon Bolts with Cross Recess on Head -- GB/T 31.1 Hexagon Bolts with Split Pin Hole on Shank -- GB/T 31.2 Hexagon Bolts with Split Pin Hole on Shank Reduced Shank Product Grade B -- GB/T 31.3 Hexagon Bolts with Split Pin Hole on Shank Fine Pitch Thread - Product Grades A and B -- GB/T 32.1 Hexagon bolts with wire holes on head Product Grades A and B -- GB/T 32.2 Hexagon Bolts with Wire Holes on Head Reduced Shank Product Grade B -- GB/T 32.3 Hexagon Bolts with Wire Holes on Head Fine Pitch Thread Product Grades A and B -- GB/T 5780 Hexagon Head Bolts Product Grade C -- GB/T 5781 Hexagon Head Bolts Full Thread Product Grade C -- GB/T 5782 Hexagon Head Bolts -- GB/T 5783 Hexagon Head Bolts Full Thread -- GB/T 5784 Hexagon Head Bolts Reduced Shank Product Grade B -- GB/T 5785 Hexagon Head Bolts Fine Pitch Thread -- GB/T 5786 Hexagon Head Bolts with Fine Pitch Thread Full Thread This Standard was drafted in accordance with the rules given in GB/T This Standard replaces GB/T , Hexagon Head Bolts. Compared with GB/T , the main technical differences are as follows: -- it deletes If, in special cases, specifications other than those listed in this Page 3 of 18
4 Standard are required, they can be selected from existing Standards, GB/T and GB/T (Chapter 1, Edition 2000); -- it unifies reference thread standards into GB/T 193 and GB/T 9145 (Chapter 2); -- it specifies the surface defects only for the steel products: GB/T (Table 3); -- it adds that the surface of steel bolts is as processed and deletes oxidized (Table 3); -- it adds the technical requirements of non-electrolytically applied zinc flake coatings of steel bolts (Table 3); -- it adds the technical requirements of passivating treatment of stainless steel nuts in accordance with GB/T (Table 3); -- it adds the technical requirements of electroplating of non-ferrous metal bolts in accordance with GB/T ; and -- it is only allowed to omit Designation that the surface is as processed (5.2). This Standard was redrafted by reference to ISO 4014:2011, Hexagon Head Bolts Product Grades A and B (English edition). The technical differences between this Standard and ISO 4014:2011 and their reasons are as follows: -- it deletes the specification of ISO 4014, If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, ISO 4753 and (Chapter 1), which does not belong to the content of this Standard; -- in the Normative References, it uses Chinese standards to replace the international standards (Chapter 2), adds the references of GB/T 90.2 (Table 3), GB/T 193 (Table 3), GB/T 9145 (Table 3), GB/T (Table 3) and GB/T 1237 (5.1), and deletes the references of ISO 724 and ISO 965-1, in order to meet Chinese basic standards of fasteners; -- it adds the technical requirements of passivating treatment of stainless steel bolts (Table 3) and extend the scope of product use; -- it adds the technical requirements of packaging (Table 3), in order to meet Chinese basic standards of fasteners; and -- it modifies the Example of Designation into the Simplified Example of Designation (5.2), in order to meet the specifications of GB/T The following editorial modifications are made in this Standard: Page 4 of 18
5 Hexagon Head Bolts 1 Scope This Standard specifies the dimensions, technical requirements and designation of hexagon head bolts. This Standard applies to hexagon head bolts with: thread M1.6 to M64; property class 5.6, 8.8, 9.8, 10.9, A2-70, A4-70, A2-50, A4-50, CU2, CU3 and AL4; and product grades A and B. Product grade A is used for bolts with d = 1.6 mm to 24 mm and l 10d or l 150 mm (whichever is smaller); and product grade B is used for bolts with d > 24 mm or l > 10d or l > 150 mm (whichever is smaller) 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition dated applies to this document. For undated references, the latest edition of the referenced document (including any amendments) applies to this Standard. GB/T 2 Fasteners Ends of Parts with External Thread (GB/T , ISO 4753:2011, MOD) GB/T 90.1 Fasteners Acceptance Inspection (GB/T , ISO 3269:2000, IDT) GB/T 90.2 Fasteners Marking and Packaging GB/T 193 General Purpose Metric Screw Threads Diameters and Pitches (GB/T , ISO 261:1998, MOD) GB/T :1986) Designation System for Fasteners (GB/T , eqv. ISO GB/T Mechanical Properties of Fasteners Bolts, Screws and Studs (GB/T , ISO 898-1:2009, MOD) GB/T Mechanical Properties of Fasteners Stainless Steel Bolts, Screws and Studs (GB/T , ISO :2009, MOD) GB/T Mechanical Properties of Fasteners Bolts, Screws, Studs and Nuts Made of Non-ferrous Metals (GB/T , eqv. ISO 8839:1986) GB/T Essential Oils and Aromatic Extracts Determination of Residual Page 6 of 18
6 Table 3 Technical Requirements and Reference Standards Non-ferrous Material Steel Stainless steel metal General technical requirements GB/T Thread Tolerance Standards GB/T 193 and GB/T g d < 3mm: as agreed; d 24 mm: A2-70, Mechanical properties Property class 3 mm d 39 mm: 5.6, 8.8 and 10.9; 3 mm d 16 mm: 9.8; d > 39 mm: as agreed A4-70; 24 mm < d 39 mm: A2-50, A4-50; d > 39 mm: as agreed CU2, CU3, AL4 Standard 3 mm d 39 mm: GB/T ; d < 3mm and d > 39 mm: as agreed d 39 mm: GB/T ; d > 39 mm: as agreed GB/T Tolerance Product d 24 mm and l 10d or l 150 mm (whichever is smaller): A; grade d > 24 mm and l > 10d or l > 150 mm (whichever is smaller): B Standard GB/T Surface discontinuity GB/T Surface process Not processed; Requirements for electroplating are specified in GB/T Requirements for non-electrolytically applied zinc flake coatings are specified in GB/T Simple process; Requirements for passivating treatment are specified in GB/T Simple process; Requirements for electroplating are specified in GB/T Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser. Acceptance and packaging GB/T 90.1 and GB/T Designation 5.1 Designation method The designation method is specified in GB/T Designation example A hexagon head bolt (product grade A) with thread M12, nominal length l = 80 mm, property class 8.8 and no surface treatment is designated as follows: Hexagon head bolt GB/T 5782 M12 80 END Page 18 of 18
--> Buy True-PDF --> Auto-delivered in 0~10 minutes. GB/T Translated English of Chinese Standard: GB/T819.
Translated English of Chinese Standard: GB/T819.2-2016 www.chinesestandard.net Sales@ChineseStandard.net NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB ICS 21.060.10 J 13 Replacing GB/T 819.2-1997
More informationGB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD OF THE
GB/T 9-00 Translated English of Chinese Standard: GB/T9-00 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS.00.0 J 0 GB/T 9-00 Replacing GB/T
More informationNATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA
Translated English of Chinese Standard: GB/T18230.1-2000 Translated by: www.chinesestandard.net Wayne Zheng et al. Email: Sales@ChineseStandard.net NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB/T
More informationGB/Z Translated English of Chinese Standard: GB/Z
Translated English of Chinese Standard: GB/Z32564-2016 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARDIZATION GUIDANCE TECHNICAL DOCUMENT OF THE PEOPLE 'S REPUBLIC OF CHINA ICS 21.060.10
More informationGB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD OF THE
Translated English of Chinese Standard: GB/T7307-2001 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 21.040.20 J 04 GB/T 7307-2001 eqv ISO
More informationISO INTERNATIONAL STANDARD. Hexagon socket head cap screws with metric fine pitch thread. Vis à tête cylindrique à six pans creux à pas fin
INTERNATIONAL STANDARD ISO 12474 First edition 2010-10-01 Hexagon socket head cap screws with metric fine pitch thread Vis à tête cylindrique à six pans creux à pas fin Reference number ISO 12474:2010(E)
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 4762 Fourth edition 2004-03-01 Hexagon socket head cap screws Vis à tête cylindrique à six pans creux Reference number ISO 4762:2004(E) ISO 2004 PDF disclaimer This PDF file
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 10511 Third edition 2012-12-15 Prevailing torque type hexagon thin nuts (with non-metallic insert) Écrous hexagonaux bas autofreinés (à anneau non métallique) Reference number
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 7380-2 First edition 2011-08-01 Button head screws Part 2: Hexagon socket button head screws with collar Vis à tête cylindrique bombée plate Partie 2: Vis à tête cylindrique
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 7051 Second edition 2011-08-01 Cross-recessed raised countersunk (oval) head tapping screws Vis à tôle à tête fraisée bombée à empreinte cruciforme Reference number ISO 7051:2011(E)
More informationISO INTERNATIONAL STANDARD. Hexagon bolts with flange Small series Product grade A
INTERNATIONAL STANDARD ISO 15071 Second edition 2011-06-01 Hexagon bolts with flange Small series Product grade A Vis à tête hexagonale à embase cylindro-tronconique Série étroite Grade A Reference number
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 4026 Third edition 2003-12-01 Hexagon socket set screws with flat point Vis sans tête à six pans creux, à bout plat Reference number ISO 4026:2003(E) ISO 2003 ISO 4026:2003(E)
More informationISO INTERNATIONAL STANDARD. Hexalobular socket cheese head screws. Vis à métaux à tête cylindrique basse à six lobes internes
INTERNATIONAL STANDARD ISO 14580 First edition 2001-09-01 Hexalobular socket cheese head screws Vis à métaux à tête cylindrique basse à six lobes internes Reference number ISO 14580:2001(E) ISO 2001 PDF
More informationIS INTERNATIONAL STANDARD. Slotted countersunk flat head screws (common head style) - Product grade A. Vis 9 mktaux d t&e fraisee fendue -
INTERNATIONAL STANDARD IS0 2009 Third edition 1994-04-01 Slotted countersunk flat head screws (common head style) - Product grade A Vis 9 mktaux d t&e fraisee fendue - Grade A Reference number IS0 2009:1994(E)
More informationISO Prevailing torque type hexagon regular nuts (with non-metallic insert) Property classes 5, 8 and 10
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 7040 Third edition 2012-12-15 Prevailing torque type hexagon regular nuts (with non-metallic insert) Property classes 5, 8 and 10 Écrous hexagonaux
More informationGB/T / ISO 594-1:1986
Translated English of Chinese Standard: GB/T1962.1-2015 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 11.040.20 C 31 GB/T 1962.1-2015 / ISO
More informationISO Prevailing torque type hexagon nuts (with non-metallic insert), style 2 Property classes 9 and 12
INTERNATIONAL STANDARD ISO 7041 Fourth edition 2012-05-15 Prevailing torque type hexagon nuts (with non-metallic insert), style 2 Property classes 9 and 12 Écrous hexagonaux autofreinés (à anneau non métallique),
More informationISO INTERNATIONAL STANDARD. Hexalobular socket pan head screws. Vis à métaux à tête cylindrique bombée large à six lobes internes
INTERNATIONAL STANDARD ISO 14583 Second edition 2011-03-15 Hexalobular socket pan head screws Vis à métaux à tête cylindrique bombée large à six lobes internes Reference number ISO 14583:2011(E) ISO 2011
More information1 Scope. 2 Normative references. 3 Dimensions. Page 2 DIN :
Page 2 1 Scope This standard specifies dimensions and technical delivery conditions for stud bolts with metric thread made of steel, stainless steel or nonferrous metal. 2 Normative references This standard
More informationISO INTERNATIONAL STANDARD. Vis a f&e hexagonale partiellement filetees - Grades A er B. Third edition
NTERNATONAL STANDARD SO 401 4 Third edition 1999-09-01 Vis a f&e hexagonale partiellement filetees - Grades A er B Reference number SO 4014:1999(E) SO 401 4:1999(E) Foreword SO (the nternational Organization
More information--> Buy True-PDF --> Auto-delivered in 0~10 minutes. GB/T Translated English of Chinese Standard: GB
Translated English of Chinese Standard: GB706-2008 www.chinesestandard.net Sales@ChineseStandard.net NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB ICS 77.140.70 H 44 Replacing GB/T 706-1988, GB/T
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 14219:2003 Hexagon bolts with flange with metric fine pitch thread - Small series Hexagon bolts with flange with metric fine pitch thread - Small series EESTI STANDARDIKESKUS EESTI
More informationGB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD OF THE
Translated English of Chinese Standard: GB/T1804-2000 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 17.040.10 J 04 GB/T 1804-2000 eqv ISO
More information--> Buy True-PDF --> Auto-delivered in 0~10 minutes. GB/T Translated English of Chinese Standard: GB/T
Translated English of Chinese Standard: GB/T6556-2016 www.chinesestandard.net Sales@ChineseStandard.net NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB ICS 21.140 J 22 Replacing GB/T 6556-1994 Type,
More informationAS/NZS 4404:1996 AS/NZS
(ISO 1482:2011, IDT) Australian/New Zealand Standard Slotted countersunk (flat) head tapping screws (common head style) Superseding AS/NZS 4404:1996 This joint Australian/New Zealand standard was prepared
More information--> Buy True-PDF --> Auto-delivered in 0~10 minutes. GB/T Translated English of Chinese Standard: GB/T
Translated English of Chinese Standard: GB/T708-2006 www.chinesestandard.net Sales@ChineseStandard.net ICS 77.140.50 H 46 NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB Replacing GB/T 708-1988
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN ISO 14583:2002 Hexalobular socket pan head screws Hexalobular socket pan head screws EESTI STANDARDIKESKUS EESTI STANDARDI EESSÕNA NATIONAL FOREWORD Käesolev Eesti standard EVS-EN
More informationGB/T Translated English of Chinese Standard: GB/T
Translated English of Chinese Standard: GB/T19348.1-2014 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 37.040.25; 19.100 J 04 GB/T 19348.1-2014
More informationISO INTERNATIONAL STANDARD. Cross recessed pan head drilling screws with tapping screw thread
INTERNATIONAL STANDARD ISO 15481 First edition 1999-08-01 Cross recessed pan head drilling screws with tapping screw thread Vis autoperceuses à tête cylindrique bombée large à empreinte cruciforme, avec
More informationISO INTERNATIONAL STANDARD. Cross recessed raised countersunk head drilling screws with tapping screw thread
INTERNATIONAL STANDARD ISO 15483 First edition 1999-08-01 Cross recessed raised countersunk head drilling screws with tapping screw thread Vis autoperceuses à tête fraisée bombée à empreinte cruciforme,
More informationISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition
INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E) ISO 2005 PDF disclaimer This
More informationFästelement Sextandhålsskruvar med cylinderhuvud (ISO 14580:2001) Hexalobular socket cheese head screws (ISO 14580:2001)
SVENSK STANDARD SS-EN ISO 14580 Fastställd 2001-09-28 Utgåva 1 Fästelement Sextandhålsskruvar med cylinderhuvud (ISO 14580:2001) Hexalobular socket cheese head screws (ISO 14580:2001) ICS 21.060.10 Språk:
More informationISO INTERNATIONAL STANDARD. Hexagon bolts with flange with metric fine pitch thread Small series Product grade A
INTERNATIONAL STANDARD ISO 15072 First edition 1999-12-15 Hexagon bolts with flange with metric fine pitch thread Small series Product grade A Vis à tête hexagonale à embase cylindro-tronconique, à filetage
More information--> Buy True-PDF --> Auto-delivered in 0~10 minutes. GB/T Translated English of Chinese Standard: GB/T
Translated English of Chinese Standard: GB/T11363-2008 www.chinesestandard.net Buy True-PDF Auto-delivery. Sales@ChineseStandard.net NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB ICS 25.160.50
More informationFästelement Sexkanthålsskruvar (ISO 4762:2004) Hexagon socket head cap screws (ISO 4762:2004)
SVENSK STANDARD SS- Fastställd 2004-03-19 Utgåva 2 Fästelement Sexkanthålsskruvar (ISO 4762:2004) Hexagon socket head cap screws (ISO 4762:2004) ICS 21.060.10 Språk: engelska Publicerad: maj 2004 Copyright
More informationISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E)
More informationGB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD OF THE
Translated English of Chinese Standard: GB/T6151-2016 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 59.080.01 W 04 GB/T 6151-2016 Replacing
More information--> Buy True-PDF --> Auto-delivered in 0~10 minutes. GB/T Translated English of Chinese Standard: GB/T
Translated English of Chinese Standard: GB/T3820-1997 www.chinesestandard.net Sales@ChineseStandard.net NATIONAL STANDARD OF GB THE PEOPLE S REPUBLIC OF CHINA ICS 59.080.30 W 04 Replacing GB 3820-1983
More informationHexagon socket set screws with cup point (ISO 4029:2003)
SVENSK STANDARD SS-EN ISO 4029:2004 Fastställd 2004-01-09 Utgåva 1 Fästelement Stoppskruvar med sexkantshål och skål (ISO 4029:2003) Hexagon socket set screws with cup point (ISO 4029:2003) ICS 21.060.10
More informationMATERIAL AND EQUIPMENT STANDARD FOR METRIC TYPE FASTENERS (SCREWS, BOLTS, STUDS, NUTS AND WASHERS) ORIGINAL EDITION DEC. 1997
MATERIAL AND EQUIPMENT STANDARD FOR METRIC TYPE FASTENERS (SCREWS, BOLTS, STUDS, NUTS AND WASHERS) ORIGINAL EDITION DEC. 1997 This Standard is the property of Iranian Ministry of Petroleum. All rights
More informationGB Translated English of Chinese Standard: GB NATIONAL STANDARD OF
Translated English of Chinese Standard: GB18099-2013 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 43.040.20 T 38 GB 18099-2013 Replacing
More informationNational Standard of The People s Republic of China
Translated English of Chinese Standard: GB/T17626.11-2008 Translated by: www.chinesestandard.net Wayne Zheng et al. Email: Sales@ChineseStandard.net ICS 33.100.20 L 06 GB National Standard of The People
More informationGB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD OF THE
Translated English of Chinese Standard: GB/T4851-2014 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 83.180 Z 38 GB/T 4851-2014 Replacing GB
More informationGB/T / ISO :1999
Translated English of Chinese Standard: GB/T2828.1-2012 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 03.120.30 A 41 GB/T 2828.1-2012 / ISO
More information--> Buy True-PDF --> Auto-delivered in 0~10 minutes. GB/T Translated English of Chinese Standard: GB/T
Translated English of Chinese Standard: GB/T13306-2011 www.chinesestandard.net Sales@ChineseStandard.net NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB ICS 21. 010 J 29 Replacing GB/T 13306-1991
More informationFästelement Sexkanthålsskruvar med sänkhuvud (ISO 10642:2004) Hexagon socket countersunk head screws (ISO 10642:2004)
SVENSK STANDARD SS-EN ISO 10642:2004 Fastställd 2004-03-19 Utgåva 2 Fästelement Sexkanthålsskruvar med sänkhuvud (ISO 10642:2004) Hexagon socket countersunk head screws (ISO 10642:2004) ICS 21.060.10 Språk:
More informationGB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD OF THE
Translated English of Chinese Standard: GB/T14214-2003 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 11.040.70 Y 89 GB/T 14214-2003 Replacing
More informationFasteners Torque/clamp force testing (ISO 16047:2005)
SVENSK STANDARD SS- Fastställd 2005-02-18 Utgåva 1 Fästelement Provning av moment/kraftutbyte (ISO 16047:2005) Fasteners Torque/clamp force testing (ISO 16047:2005) ICS 21.060.01 Språk: engelska Publicerad:
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN ISO 14579:2002 Hexalobular socket head cap screws Hexalobular socket head cap screws EESTI STANDARDIKESKUS EESTI STANDARDI EESSÕNA NATIONAL FOREWORD Käesolev Eesti standard EVS-EN
More informationISO INTERNATIONAL STANDARD. Tapping screw and washer assemblies with plain washers. Vis à tôle à rondelle plate imperdable
INTERNATIONAL STANDARD ISO 10510 Second edition 2011-04-01 Tapping screw and washer assemblies with plain washers Vis à tôle à rondelle plate imperdable Reference number ISO 10510:2011(E) ISO 2011 ISO
More informationISO INTERNATIONAL STANDARD. Fasteners Non-electrolytically applied zinc flake coatings
INTERNATIONAL STANDARD ISO 63 First edition 2000-07-1 Fasteners Non-electrolytically applied zinc flake coatings Éléments de fixation Revêtements non électrolytiques de lamelles de zinc Reference number
More informationAustralian Standard. ISO metric hexagon bolts and screws Product grades A and B. Part 1: Bolts AS ISO 4014:1999
AS 1110.12000 ISO 4014:1999 AS 1110.1 Australian Standard ISO metric hexagon bolts and screws Product grades A and B Part 1: Bolts [ISO title: Hexagon head boltsproduct grades A and B] This Australian
More informationOrganic Products Part 4: Management System
Translated English of Chinese Standard: GB/T19630.4-2011 Translated by: www.chinesestandard.net Wayne Zheng et al. Email: Sales@ChineseStandard.net ICS 65.020.01 B 04 NATIONAL STANDARD OF THE PEOPLE S
More informationJB/T Translated English of Chinese Standard: JB/T
Translated English of Chinese Standard: JB/T9249-1999 www.chinesestandard.net Sales@ChineseStandard.net MACHINERY INDUSTRY STANDARD OF JB THE PEOPLE S REPUBLIC OF CHINA ICS 17.120 N 12 JB/T 9249-1999 Replacing
More informationMechanical Properties of Fasteners - Bolts, Screws and Studs
ICS 21.060.10 J 13 NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB/T 3098.1-2010 Replace GB/T 3098.1-2000 Mechanical Properties of Fasteners - Bolts, Screws and Studs 紧固件机械性能螺栓, 螺钉和螺柱 (ISO 898-1:
More informationISO INTERNATIONAL STANDARD. Welding Studs and ceramic ferrules for arc stud welding
INTERNATIONAL STANDARD ISO 13918 Second edition 2008-02-15 Welding Studs and ceramic ferrules for arc stud welding Soudage Goujons et bagues céramiques pour le soudage à l'arc des goujons Reference number
More informationHexagon socket button head screws (ISO 7380:2004)
SVENSK STANDARD SS-EN ISO 7380:2004 Fastställd 2004-02-06 Utgåva 2 Fästelement Sexkanthålsskruvar med rundat huvud (ISO 7380:2004) Hexagon socket button head screws (ISO 7380:2004) ICS 21.060.10 Språk:
More informationISO INTERNATIONAL STANDARD. Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C
INTERNATIONAL STANDARD ISO 4759-1 Second edition 2000-11-15 Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C Tolérances des éléments de fixation Partie 1: Vis, goujons
More informationGB/T Translated English of Chinese Standard: GB/T
Translated English of Chinese Standard: GB/T4808.2-2008 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 9.080.30 W04 GB/T 4802.2-2008 Replacing
More informationComparable ISO Standard. Date of current standard/modified
Title Standard All-metal prevailing torque All-metal prevailing torque EN ISO EN ISO Comparable ISO Standard Date of current standard/modified 980 7042 27042 7042 1998-02 980 10513 30513 10513 1998-02
More informationQB/T Translated English of Chinese Standard: QB/T
Translated English of Chinese Standard: QB/T1337-2010 www.chinesestandard.net Sales@ChineseStandard.net QB LIGHT INDUSTRY STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 97.180 Classification number: Y50
More informationGB/T Translated English of Chinese Standard: GB/T
Translated English of Chinese Standard: GB/T33014.2-2016 www.chinesestandard.net Sales@ChineseStandard.net How to BUY & immediately GET a full-copy of this standard? 1. GB/T 33014.2-2016 www.chinesestandard.net;
More information3. ISO information on technical standardisation changeover to ISO
3. ISO information on technical standardisation changeover to ISO 3.1 Code Technical standardisation is work of harmonisation in the technical field that is carried out jointly by all interested parties.
More informationISO INFORMATION ON TECHNICAL STANDARDISATION CHANGEOVER TO ISO
ISO INFORMATION ON TECHNICAL STANDARDISATION 3.1 Code Technical standardisation is work of harmonisation in the technical field that is carried out jointly by all interested parties. Its aim is to stipulate,
More informationAS/NZS 1214:2016 Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series) AS/NZS 1214:2016
(ISO 10684:2004, MOD) Australian/New Zealand Standard Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series) AS/NZS 1214:2016 This joint Australian/New Zealand standard was
More informationISO INTERNATIONAL STANDARD. Fasteners Hot dip galvanized coatings. Éléments de fixation Revêtements de galvanisation à chaud
INTERNATIONAL STANDARD ISO 10684 First edition 2004-07-15 Fasteners Hot dip galvanized coatings Éléments de fixation Revêtements de galvanisation à chaud Reference number ISO 10684:2004(E) ISO 2004 PDF
More informationQB/T Translated English of Chinese Standard: QB/T LIGHT INDUSTRY STANDARD OF
Translated English of Chinese Standard: QB/T2155-2010 www.chinesestandard.net Buy True-PDF Auto-delivery. Sales@ChineseStandard.net QB LIGHT INDUSTRY STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 59.140.35
More informationScrew and washer assemblies made of steel with plain washers Washer hardness classes 200 HV and 300 HV
BRITISH STANDARD BS EN ISO 10644:2009 Screw and washer assemblies made of steel with plain washers Washer hardness classes 200 HV and 300 HV ICS 21.060.10; 21.060.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT
More information--> Buy True-PDF --> Auto-delivered in 0~10 minutes. FZ/T
Translated English of Chinese Standard: FZ/T50010.13-2011 www.chinesestandard.net Sales@ChineseStandard.net NATIONAL TEXTILE INDUSTRY STANDARD OF THE PEOPLE S REPUBLIC OF CHINA FZ ICS 59.060.20 W 50 FZ/T
More informationAustralian Standard. ISO metric hexagon bolts and screws Product grade C. Part 1: Bolts AS ISO 4016:1999
AS 1111.12000 ISO 4016:1999 AS 1111.1 Australian Standard ISO metric hexagon bolts and screws Product grade C Part 1: Bolts [ISO title: Hexagon head boltsproduct grade C] This Australian Standard was prepared
More informationNPS/001/010 Technical Specification for Fasteners and Fixings for Wood Pole Overhead Lines and General Construction Works
Version:- 4.0 Date of Issue:- August 2014 Page 1 of 13 NPS/001/010 Technical Specification for Fasteners and Fixings for Wood Pole Overhead Lines and General Construction Works 1. Purpose The purpose of
More informationTB/T Translated English of Chinese Standard: TB/T RAILWAY INDUSTRY STANDARD
Translated English of Chinese Standard: TB/T 1618-2001 www.chinesestandard.net Sales@ChineseStandard.net RAILWAY INDUSTRY STANDARD TB OF THE PEOPLE S REPUBLIC OF CHINA TB/T 1618-2001 eqv ISO 5948:1994
More informationISO 8752 INTERNATIONAL STANDARD. Spring-type straight pins Slotted, heavy duty
INTERNATIONAL STANDARD ISO 8752 Third edition 2009-06-15 Spring-type straight pins Slotted, heavy duty Goupilles cylindriques creuses, dites goupilles élastiques Série épaisse Reference number ISO 8752:2009(E)
More informationProvläsningsexemplar / Preview INTERNATIONAL STANDARD. Aerospace MJ threads Part 1: General requirements
INTERNATIONAL STANDARD ISO 5855-1 Third edition 1999-10-15 Aerospace MJ threads Part 1: General requirements Aéronautique et espace Filetage MJ Partie 1: Exigences générales A Reference number Foreword
More informationFasteners Non-electrolytically applied zinc flake coatings
INTERNATIONAL STANDARD ISO 10683 Second edition 2014-05-15 Fasteners Non-electrolytically applied zinc flake coatings Fixations Revêtements non électrolytiques de zinc lamellaire Reference number ISO 2014
More informationAustralian/New Zealand Standard
AS/NZS 2451:1998 Australian/New Zealand Standard Bolts, screws and nuts with British Standard Whitworth threads (rationalized series) AS/NZS 2451:1998 This Joint Australian/New Zealand Standard was prepared
More informationInstructions for Use of Products of Consumer Interest- Part 4: Textiles and Apparel
Translated English of Chinese Standard: GB5296.4-2012 Translated by: www.chinesestandard.net Wayne Zheng et al. Email: Sales@ChineseStandard.net ICS 03.080.30; 59.080.01 A 12 NATIONAL STANDARD OF THE PEOPLE
More informationScheduling, dimensioning, bending and cutting of steel reinforcement for concrete Specification
BRITISH STANDARD BS 8666:2005 Incorporating Amendment No. 1 Scheduling, dimensioning, bending and cutting of steel reinforcement for concrete Specification ICS 77.140.15; 91:080.40 Committees responsible
More informationISO metric hexagon bolts and screws Product grade C. Part 1: Bolts AS :2015 ISO 4016:2011
AS 1111.1:2015 ISO 4016:2011 AS 1111.1:2015 ISO metric hexagon bolts and screws Product grade C Part 1: Bolts This Australian Standard was prepared by Committee ME-029, Fasteners. It was approved on behalf
More informationSOUTH AFRICAN NATIONAL STANDARD
ICS 21.060.20 ISBN 0-626-15095-7 SANS 1700-14-11:2003 ISO 7417:1984 SOUTH AFRICAN NATIONAL STANDARD Fasteners Part 14: Hexagon nuts Section 11: Hexagon nuts for structural bolting Style 2, hot-dip galvanized
More informationYY / ISO 15223:2000
Translated English of Chinese Standard: YY0466-2003 www.chinesestandard.net Sales@ChineseStandard.net ICS 11.040.01 C 30 PHARMACEUTICAL INDUSTRY STANDARD OF THE PEOPLE S REPUBLIC OF CHINA YY / ISO 15223:2000
More informationSPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS
UDC 621.882.211 [669.14.018.291] IS : 3757-1985 (Reaffirmed 2003) Edition 3.2 (1989-07) Indian Standard SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS ( Second Revision ) (Incorporating Amendment Nos.
More information--> Buy True-PDF --> Auto-delivered in 0~10 minutes. GB/T Translated English of Chinese Standard: GB/T
Translated English of Chinese Standard: GB/T33877-2017 www.chinesestandard.net Sales@ChineseStandard.net NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB ICS 19.100 J 04 Non-Destructive Testing Test
More informationGB / IEC/CISPR 11:2010
Translated English of Chinese Standard: GB4824-2013 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 33.100 L 06 GB 4824-2013 / IEC/CISPR 11:2010
More informationISO INTERNATIONAL STANDARD. Fasteners Hot dip galvanized coatings. Éléments de fixation Revêtements de galvanisation à chaud
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 10684 First edition 2004-07-15 Fasteners Hot dip galvanized coatings Éléments de fixation Revêtements de galvanisation à chaud Reference number
More informationGB Translated English of Chinese Standard: GB National Standard of the People's Republic of China
Translated English of Chinese Standard: GB17625.1-2012 ICS 33.100.10 L 06 GB National Standard of the People's Republic of China GB 17625.1-2012 Replacing GB 17625.1-2012 Electromagnetic compatibility
More informationDocument comprises 11 pages 03.15
Document comprises 11 pages 03.15 A comma is used as the decimal marker. National foreword This document (EN 14399-6:2015) has been prepared by Technical Committee CEN/TC 185 Fasteners (Secretariat: DIN,
More informationTesting of friction properties of fasteners
2018-02-13 Sida 1 (31) Testing of friction properties of fasteners Contents 1 Introduction 2 2 Scope 2 3 Terms and definitions 3 4 Structure of evaluation of friction properties 5 5 Cleaning of test parts
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN ISO 16047:2005 Fasteners - Torque/clamp force testing Fasteners - Torque/clamp force testing EESTI STANDARDIKESKUS EESTI STANDARDI EESSÕNA NATIONAL FOREWORD Käesolev Eesti standard
More informationISO 262 INTERNATIONAL STANDARD. ISO general purpose metric screw threads Selected sizes for screws, bolts and nuts
INTERNATIONAL STANDARD ISO general purpose metric screw threads Selected sizes for screws, bolts and nuts A ISO 6 Second edition 998--5 Filetages métriques ISO pour usages généraux Sélection de dimensions
More informationQB/T Translated English of Chinese Standard: QB/T LIGHT INDUSTRY STANDARD
Translated English of Chinese Standard: QB/T4348-2012 www.chinesestandard.net Sales@ChineseStandard.net ICS 71.100.40 Classification number: Y 43 Registration number: 36751-2012 LIGHT INDUSTRY STANDARD
More informationGB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD OF THE
Translated English of Chinese Standard: GB/T519-2017 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 83.160.01 G 41 GB/T 519-2017 Replacing
More informationISO INTERNATIONAL STANDARD. Fasteners Hot dip galvanized coatings. Éléments de fixation Revêtements de galvanisation à chaud
INTERNATIONAL STANDARD ISO 10684 First edition 2004-07-15 Fasteners Hot dip galvanized coatings Éléments de fixation Revêtements de galvanisation à chaud Reference number ISO 2004 PDF disclaimer This PDF
More informationGB/T / CISPR 15:2005
Translated English of Chinese Standard: GB17743-2007 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 33.100 L 06 GB/T 17743-2007 / CISPR 15:2005
More informationISO 5858 Aerospace Nuts, self-locking, with maximum operating temperature less than or equal to 425 C Procurement specification
INTERNATIONAL STANDARD ISO 5858 Second edition 1999-11-15 Corrected and reprinted 2000-11-15 Aerospace Nuts, self-locking, with maximum operating temperature less than or equal to 425 C Procurement specification
More informationBOLTS, SCREWS, NUTS AND PLAIN WASHERS
BRITISH STANDARD SPECIFICATION UNIFIED BLACK HEXAGON BOLTS, SCREWS, NUTS AND PLAIN WASHERS (UNC & UNF THREADS) B Te HEAVY SERIES B.S. 1769 : 1951 incorporating amendments issued March 1955 (PD 2141) May
More informationPolygonal taper interface with flange contact surface. Part 1: Dimensions and designation of shanks
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 26623-1 Second edition 2014-09-01 Polygonal taper interface with flange contact surface Part 1: Dimensions and designation of shanks Interfaces
More informationGB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD
Translated English of Chinese Standard: GB/T20808-2011 www.chinesestandard.net Email: Sales@ChineseStandard.net ICS 85.060 GB Y 32 NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB/T 20808-2011 Partly
More informationISO INTERNATIONAL STANDARD. Assembly tools for screws and nuts Driving squares Part 1: Driving squares for hand socket tools
INTERNATIONAL STANDARD ISO 1174-1 Second edition 2011-04-15 Assembly tools for screws and nuts Driving squares Part 1: Driving squares for hand socket tools Outils de manœuvre pour vis et écrous Carrés
More informationAS Australian Standard METRIC SCREW THREADS FOR FASTENERS. This is a free 6 page sample. Access the full version online.
AS 1275 1985 Australian Standard METRIC SCREW THREADS FOR FASTENERS This Australian standard was prepared by Committee ME/28, Screw Threads. It was approved on behalf of the Council of the Standards Association
More information