How To Make Faux Leather Tassels

Transcription

1 Published on Sew4Home How To Make Faux Leather Tassels Editor: Alicia Thommas.Designer.Sew4Home Tuesday, 22 November :00 When a box of faux leather arrived from Fabric.com, it ended up sitting on the floor next to a paper shredder. I had to wonder: do these two things mix? At the risk of having the evidence permanently ensnarled in the teeth of the old paper shredder, I fed it a swatch of faux leather, stopping with a half inch remaining uncut. I used the reverse switch to remove it, and ended up with a nice little fringe. Where the shredder didn't cut all the way through, it scored it well enough that it took less than two minutes to finish using scissors. The result: perfect fringe. Roll it up and you get a pretty tassel. Fabric and Other Supplies

2 For one tassel: ONE 8" x 3" scrap of faux leather. We used Faux Leather Fabric Bison Fudge from Fabric.com ONE large bead cap (16-18mm) flexible bronze and copper work best. (You can find bead caps at beading supply stores, most craft stores, and online. The best source I've found for the large flexible bronze and copper bead caps is Etsy. Copper and bronze bead caps are very inexpensive and you should find many pretty options.) ONE 6" piece of thin waxed cotton cord or leather lace (Confirm that your cord, when looped, fits through the hole in the bead cap. You can use an awl to make the hole a little bigger if necessary.) Fabric glue (not spray) Sharp scissors Optional: paper shredder (standard strip shredder) Make the Tassel Fringe Confession: these are the first two tassels I've made this way, so I consider the concept a work in progress. In other words, we're beta testing these tassels prior to using them in an upcoming project. 1. For a chunky three-inch tassel like those shown, cut an 8" x 3" piece of faux leather. (You can make your tassels thinner or longer by adjusting how you cut your faux leather.) 2. Use a fabric pen or piece of masking tape to mark the top half inch of the faux leather rectangle this is the area that will remain uncut: Option 1: Paper Shredder

3 Caution: The S4H studio has two paper shredders. One worked better than the other, but neither jammed. After using it to make two tassels, the paper shredder still shredded paper perfectly. However, this is a very limited test, so do this at your own risk. Cutting the faux leather with my rotary cutter was like cutting butter an easy clean cut. I can't say, however, that using your shredder on faux leather will not dull your paper shredder blades. 1. With one finger on the start/stop button evenly feed the faux leather into a paper shredder. WATCH CAREFULLY and hit stop when the tape is just at the blades. Hit reverse to back the piece out. My ancient shredder cut either fully or partly into the faux leather. It's worth a practice run or two with a piece of paper until you've got the rhythm down. 2. Where it doesn't cut all the way through, it does score the faux leather nicely, making a perfect channel for cutting through with your scissors. Option 2: Scissors It takes longer to make the fringe with scissors, and the results were slightly less perfect. But when rolled up, the test scissorcut fringe looked almost as nice as the paper shredder finge. 1. You can use a fabric marking pen to draw lines approximately 10mm (or ³ ₈") apart on the back of your faux leather rectangle. If you have a good eye and a steady hand, you can just hand cut the fringe without marking. Assemble Your Tassel 1. Cut a piece of your thin cord approximately 6½" long. Tie a tight knot in either end. The knots keep the loop from pulling through the bead cap.

4 2. With your fringe backing side up, apply a THIN strip of fabric glue as shown: 3. Loop the knotted cord as shown, offseting the knots: 4. Roll the fringe tightly so there are no gaps, but not to the point where you are straining the fabric.

5 5. Hold for a minute or two until the glue sets enough to hold the tassel together. 6. Feed the loop in the cord through the center of the bead. I used an unfolded paperclip to help push it through. 7. Add a small amount of glue to the top sides of the tassel where it will be hidden beneath the bead cap. Move the bead cap all the way down onto the tassel and hold for a minute while the glue sets.

6 Hints and Tips The photo below shows two flexible copper bead caps and two non-flexible metal caps (the cone shape). Either works, but the flexible caps are much easier to work with and can be crimped to fit if needed. Fabric Art & Accents This project and patterns (if any) may be downloaded for personal use only. No electronic or printed reproduction permitted without the prior written consent of Sew4Home LLC. Copyright Sew4Home LLC. All Rights Reserved. Source URL: