Lubricating Cleaning Unjamming machines and equipment PPT-SM-LOTO
|
|
- Harry Palmer
- 6 years ago
- Views:
Transcription
1 Lockout/Tagout
2 Lockout and tagout procedures should be used to safeguard workers from the unexpected startup or release of stored energy during service or maintenance activities like Lubricating Cleaning Unjamming machines and equipment PPT-SM-LOTO
3 Lockout is when a lockout device is applied to equipment and machinery PPT-SM-LOTO
4 Lockout devices hold energy isolating devices in a safe or OFF position They prevent machines or equipment from becoming energized because they are positive restraints that no one can remove without a key or other unlocking mechanism PPT-SM-LOTO
5 Tagout is when a tagout device, like a tag, is applied to equipment and machinery Tags are warning devices that authorized workers fasten to energy isolating devices to warn other workers not to start the machine while it is being serviced or undergoing maintenance PPT-SM-LOTO
6 Tagout devices are easier to remove and provide less protection than lockout devices PPT-SM-LOTO
7 When both lockout and tagout are used, it is known as LOTO PPT-SM-DFWP
8 Companies must make sure workers Understand the purpose and function of the energy control program Are trained in the safe application, use, and removal of LOTO devices PPT-SM-DFWP
9 There are three levels of LOTO training Authorized worker Affected worker Other worker PPT-SM-LOTO
10 Authorized workers lock out and tag out machines or equipment to perform servicing and maintenance PPT-SM-LOTO
11 Affected workers operate and use machines or equipment that is under LOTO They do not perform LOTO or service and maintenance on machines or equipment PPT-SM-LOTO
12 Other workers may be in the area where LOTO procedures are happening They are informed about the LOTO procedures Equipment that is being serviced or undergoing maintenance Locks or tags put into place to prevent the startup of the machine or equipment PPT-SM-LOTO
13 Companies will have their own LOTO policies and procedures OSHA recommends LOTO be performed according to a six-step procedure PPT-SM-LOTO
14 1. Prepare for shutdown by Getting permission to work on equipment with a JSA or LOTO work permit Gathering all written LOTO procedures Identifying the location of energy isolation devices Getting all equipment needed and information on the type and amount of energy you are working with PPT-SM-DFWP
15 2. Shut down equipment using normal controls 3. Isolate the equipment by turning all energy isolation devices to the OFF or closed position 4. Apply LOTO devices by having the authorized worker put a lock, tag, or both on each energy isolation device PPT-SM-DFWP
16 5. Release all stored energy and set up the machine or equipment so that it cannot collect energy Check the machine or equipment periodically to make sure stored energy is not collecting PPT-SM-DFWP
17 6. Confirm equipment isolation by trying to start up the machine or equipment using normal operating controls Equipment is not isolated if it starts up or if the lights come on Confirm isolation using tools like a voltmeter Do not use tools to confirm isolation if you are not trained and authorized PPT-SM-DFWP
18 Certain procedures must be followed before LOTO devices are removed and energy is restored to the machine or equipment The work area must be inspected to make sure unnecessary items have been removed and machine and equipment parts are in place and working Make sure all workers in the surrounding area are removed or are in a safe position Confirm that the machine or equipment controls are in neutral PPT-SM-LOTO
19 Remove the LOTO devices and notify affected workers that the devices have been removed Re-energize the machine or equipment PPT-SM-LOTO
20 Each LOTO device must be removed from each energy isolating device by the worker who applied the device PPT-SM-LOTO
21 21
22 Sign and date this quiz sheet. Circle the letter representing the correct answer to each quiz question below. Name: Date: LOTO Safety Meeting Quiz: LOTO 1. procedures should be used to safeguard workers from the unexpected startup or release of stored energy during service or maintenance activities. A. Stop work B. Lockout and tagout C. Confined space D. Energization 2. devices are positive restraints that no one can remove without a key or other unlocking mechanism. A. Lockout devices B. Warning tags C. Product labels D. Energy isolating 6. workers lock out and tag out machines or equipment to perform servicing and maintenance. A. Other B. Authorized C. Affected D. Unqualified 7. workers operate and use machines or equipment that is under LOTO, but do not perform LOTO or service and maintenance on machines or equipment. A. Other B. Affected C. Authorized D. Unqualified 3. is when a tagout device is applied to equipment and machinery. A. First aid B. Lockout C. Fall protection D. Tagout 4. are warning devices that let other workers know not to start the machine while it is being serviced or undergoing maintenance. A. Locks B. Signs C. Tags D. Energy isolating devices 5. When both lockout and tagout are used, it is known as. A. OSHA B. NFPA C. LOTO D. ANSI 8. workers may be in the area where LOTO procedures are happening. A. Other B. Affected C. Authorized D. Unqualified 9. recommends LOTO be performed according to a six-step procedure. A. NASA B. OSHA C. ANSI D. API 2015 PEC Safety, Inc. 10. Each LOTO device must be removed from each energy isolating device by. A. A rescue worker B. Any worker who is available and in the area C. A supervisor D. The worker who applied the device QUIZ-SM-LOTO NOV 2015
23 Instructors: The following key shows the answers for the LOTO safety meeting quiz. 1. B 2. A 3. D 4. C 5. C 6. B 7. B 8. A Safety Meeting Answer Keys: LOTO 9. B 10. D 2015 PEC Safety, Inc. KEY-SM-LOTO NOV 2015
24 This is to certify that has successfully completed the PEC Safety Meeting Lockout/Tagout Instructor Date Awarded
25 STUDENT ROSTER INSTRUCTOR NAME SAFETY MEETING NAME SAFETY MEETING DATE COMPANY NAME Student Instructions: Print and sign your name. Also, provide your date of birth or the last four digits of your social security number PRINT STUDENT NAME (CLEARLY) STUDENT SIGNATURE LAST 4 SSN or DOB 2014 PEC Safety, Inc. All rights reserved.
Risk Management Department. Control of Hazardous Energy
Risk Management Department Control of 1 Introduction Power tools, machinery and devices make our lives easier and our jobs more productive. However, the tools, machines and systems we use every day can
More informationLOCKOUT / TAGOUT PROGRAM
Page 1 of 7 1. SCOPE LOCKOUT / TAGOUT PROGRAM This Program outlines the purpose, rules, responsibilities and techniques to be followed by all University of Pittsburgh employees to guard against the unexpected
More informationSafeguarding Machinery
Safeguarding Machinery Safeguards are essential for protecting workers from preventable injuries caused by moving machine parts. Any machine part, function, or process that may cause injury must be safeguarded.
More informationCan an Interlocked Guard take the Place of LockOut/TagOut?
Can an Interlocked Guard take the Place of LockOut/TagOut? Yes, if the Requirements of the Minor Servicing Exception are Met Jeffery H. Warren, PhD, PE, CSP A forge operator s right hand and arm had to
More informationCredentialing Achievement Record
Credentialing Achievement Record CNC Lathe Operator Level I National Institute for Metalworking Skills 10565 Fairfax Boulevard, Suite 203 Fairfax, VA 2203 FAX: 703-352-4991 http://nims-skills.org Level
More information2017 ELECTRICAL SAFETY SERVICES. Arc Flash Electrical Maintenance Lockout/Tagout And More
2017 ELECTRICAL SAFETY SERVICES Arc Flash Electrical Maintenance Lockout/Tagout And More ABOUT LEWELLYN TECHNOLOGY Improving workplace safety since 1993 Daryn Lewellyn founded Lewellyn Technology more
More informationBulletin 509 Three Phase Full Voltage NEMA Starters Size 9 Series A. Renewal Parts
Bulletin 509 Three Phase Full Voltage NEMA Starters Size 9 Series A Renewal Parts Warning: To avoid hazards of electrical shock, remove all power before proceeding. Auxiliary contacts commonly control
More informationMachine Guarding. OSHA Office of Training and Education 1
Machine Guarding OSHA Office of Training and Education 1 Introduction Crushed hands and arms, severed fingers, blindness - the list of possible machinery-related injuries is as long as it is horrifying.
More informationSafety Instructions Manual Original Instructions - RRM2
Radius Roller RRM2 Safety Instructions Manual Original Instructions - RRM2 Safety Manual 1 General Operator and Supervisor Information Signal Word Definition Signal Word Panel 2 Shop Press Signal Word
More informationElectro-Technical Rating on Vessels Powered by Main Propulsion Machinery of 750 kw / 1,000 HP Propulsion Power or More
Record of Assessment for Electro-Technical Rating on Vessels Powered by Main Propulsion Machinery of 750 kw / 1,000 HP Propulsion Power or More Print Name of Candidate Candidate s Signature Mariner Reference
More informationMinnesota Rules, Chapter 4732 X-ray Revision
Minnesota Rules, Chapter 4732 X-ray Revision PROPOSED DRAFT GAUGING X-RAY SYSTEMS, 1.0 4732.#### GAUGING X-RAY SYSTEMS. Subpart 1. Applicability. A registrant s gauging x-ray system must comply with the
More informationNC Employees Workplace Program Requirements for Safety and Health. Machine Guarding
Scope Machine Guarding A wide variety of mechanical motions and actions on machines may present hazards to employees. These can include movement of rotating members, reciprocating arms, moving belts, meshing
More informationElectrical testing safety Part 1: Preparing for absence of voltage testing
APPLICATION NOTE Electrical testing safety Part 1: Preparing for absence of voltage testing James R. White, Training Director, Shermco Industries, Inc. OSHA and the NFPA 70E Standard for Electrical Safety
More information2015 NFPA 70E. SESHA 2015 ARIZONA MINI CONFERENCE December 10, 2015 Intel Corporation
2015 NFPA 70E SESHA 2015 ARIZONA MINI CONFERENCE December 10, 2015 Intel Corporation Introduction Jeffrey A. Pugh, P.E. Pugh Engineering LLC Bachelor of Science Degrees in Electrical Engineering and Computer
More informationLockout/Tagout (LOTO) Requirements Webinar. Copyright 2017 APPA Leadership in Educational Facilities. All Rights Reserved.
Lockout/Tagout (LOTO) Requirements Webinar APPA Standards and Codes Council APPA s standards and codes activities rest on three core principles, tied to APPA s strategic vision and grounded in its mission
More informationJARVIS. Model Brisket Scissor EQUIPMENT... TABLE OF
Model 423-17 Brisket Scissor EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Model 423--17... 4037003 Air Filter / Regulator / Lubricator 3022003 Air Hose Assembly... 3059018 Balancer...
More informationPRODUCTIVELY SAFER LOCK-OUT TAG-OUT PROCEDURE
PRODUCTIVELY SAFER LOCK-OUT TAG-OUT PROCEDURE with PESDs WRITTEN BY: Philip B. Allen, Owner and CEO 1515 W. Kimberly Road Davenport, Iowa 52807, USA 1.800.280.9517 www.graceport.com PRODUCTIVELY SAFER
More informationEZ-SKIRT. Conveyor Skirting System. Installation and Users Manual. Manufactured by
EZ-SKIRT Conveyor Skirting System Installation and Users Manual Manufactured by Nelson Williams Linings, Inc. 8330 Jasmine Street PO Box 476 Mountain Iron, MN 55768 218-741-1080 May 2011 INTRODUCTION The
More informationKRM-K-LLCPC-T KRM LOTO LOCKABLE LOTO CARRY PERMIT CENTER / LOTO CARRY CENTER / LOTO PADLOCK CENTER
KRM LOTO LOCKABLE LOTO CARRY PERMIT CENTER / LOTO CARRY CENTER / LOTO PADLOCK CENTER LOTO Permit Document Carry Centre/Holder made from Hollow Transparent Tube Standard length of tube 380 mm and dia. 40
More informationMill Safety Competencies
Mill Safety Competencies The following list of competencies is presented to ensure the contents of a training program from a perspective of safety. Additional instruction in actual tool use would augment
More information2014 NEC Changes Part 1
www.garyklinka.com Page 1 of 8 Instructions: Fee $20 1. Print these pages. 2. Circle the correct answers and transfer them to the answer sheet. 3. Page down to the last page for the verification forms
More informationArc Flash Analysis Training
Arc Flash Analysis Training Contact us Today for a FREE quotation to deliver this course at your company?s location. https://www.electricityforum.com/onsite-training-rfq An arc flash analysis study is
More informationMiTek Machinery Service Bulletin
MiTek Machinery Service Bulletin Product(s) Affected Description Cyber, Cyber A/T, SmartSet, SmartSet Pro, EasySet, and CombiSet Saws Installation of a Date 05/16/2003 MiTek 301 Fountain Lakes Industrial
More informationOAK GROVE PLANT MAINTENANCE SECTION-MECHANICAL
UNIT 1 PULVERIZER SYSTEM SEMI-ANNUAL INSPECTION OG-MSM-229 EFFECTIVE DATE: PREPARED BY (Print): TOM PERSON 8/31/21 EXT: 6395 TECHNICAL REVIEW BY (Print): EXT: APPROVED BY: DATE: OG-MSM-229 PAGE 2 OF 24
More informationOwner s Manual POWER SYSTEMS, INC. GENERACR. Automatic Transfer Switch. Model Numbers , , ,
POWER SYSTEMS, INC. Owner s Manual GTS W Type GENERACR Automatic Transfer Switch 200 through 400 amp, 600 volts Model Numbers. 004940-2, 004941-2, 004942-2, 004943-2 This manual should remain with the
More information0E4343-F LOAD CIRCUIT BREAKER ACCESS DOOR P/N 0E4708 REV.- TVSS STATUS UTILITY FAULT ( RED - SURGE FAILURE )
0E4343-F 028729-E-H UTILITY SOURCE AVAILABLE SYSTEM TEST NORMAL TEST MODE AUTOMATIC MODE FAST TEST MODE CLOSED TO UTILITY INTEGRATED LOAD CENTER ATS STATUS LOAD CLOSED TO GENERATOR TVSS STATUS GENERATOR
More informationRemoval of the F/8 Secondary from the 4M Prime Focus Assembly
Doc #: 2100-AD-015-0058 Revision: - Removal of the F/8 Secondary from the 4M Prime Focus Assembly Author(s): Will Goble, Matthew Evatt, Miranda Saucedo Contents Revision History... 3 1.0 Purpose... 4 2.0
More informationWhat is RADAR? Introduction to RADAR
Introduction to RADAR What is RADAR? A hazard assessment process that can be used to help safely address upset conditions and prevent incidents from occurring Note: The RADAR process is not a new safety
More informationWhat is RADAR? A hazard assessment process that can be used to help safely address upset conditions and prevent incidents from occurring
Introduction to RADAR What is RADAR? A hazard assessment process that can be used to help safely address upset conditions and prevent incidents from occurring Note: The RADAR process is not a new safety
More informationMechatronics-Level 1
Measuring What Matters in Job Ready Assessment Blueprint Mechatronics-Level 1 Test Code: 2040 / Version: 01 Copyright 2012 General Assessment Information General Assessment Information Written Assessment
More informationGrain Elevator Safety
Grain Elevator Safety Brad Freeman, CIH, CSP Gary Hulbert, CHMM, CSP Grain Elevator Overview Types and components of grain elevators OSHA standards Hazards associated with grain handling facilities: Engulfment
More informationC H A M B E R O F C O M M E R C E O F T H E U N I T E D S T A T E S O F AMERICA
C H A M B E R O F C O M M E R C E O F T H E U N I T E D S T A T E S O F AMERICA R A N D E L K. JOHNSON S E N I O R V I C E P R E S I D E N T L A B O R, I M M I G R A T I O N & E M P L O Y E E B E N E F
More informationMAINTENANCE GUIDE ULTRAEDGE LHD LIP SHROUD SYSTEM INSTALLATION, MAINTENANCE AND REMOVAL INSTRUCTIONS
MAINTENANCE GUIDE ULTRAEDGE LHD LIP SHROUD SYSTEM INSTALLATION, MAINTENANCE AND REMOVAL INSTRUCTIONS Safety General Safety Information The safety practices described in this manual are meant as guidelines
More informationShrinker and stretcher
Shrinker and stretcher Model 96465 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein 3491 Mission Oaks Blvd, Camarillo,
More informationMinnesota Rules, Chapter 4732 X-ray Revision PROPOSED NON-MEDICAL ANALYTICAL X-RAY SYSTEMS, 1.0
Minnesota Rules, Chapter 4732 X-ray Revision PROPOSED NON-MEDICAL ANALYTICAL X-RAY SYSTEMS, 1.0 4732.#### NON-MEDICAL ANALYTICAL X-RAY SYSTEMS Subpart 1. Applicability. A registrant s analytical x-ray
More informationInformative (*Customer to review then remove this page from submitted witness test procedure)
WITNESS TEST PROEDURE TEMPLTE National Grid Use Only: Doc. # PR.756..12.16 Publication Date: 12/6/16 Document Sponsor: Neil F. Larake, Retail onnections Policy & Standards Next Scheduled Review: 8/1/17
More informationNew Developments in Regulation of U.S. Offshore Oil and Gas Operations
New Developments in Regulation of U.S. Offshore Oil and Gas Operations Peking University Law School and The University of Texas School of Law Carol Dinkins Partner Vinson & Elkins, LLP August 21, 2012
More informationMinnesota Rules, Chapter 4732 X-ray Revision PROPOSED NON-MEDICAL CABINET X-RAY SYSTEMS, 1.0
Minnesota Rules, Chapter 4732 X-ray Revision PROPOSED NON-MEDICAL CABINET X-RAY SYSTEMS, 1.0 4732.#### NON-MEDICAL CABINET X-RAY SYSTEMS Subpart 1. Applicability. A registrant s non-medical cabinet x-ray
More informationSpanish Language Safety Training Videos for Loan!
2005 OSHA RESOURCE CENTER LOAN PROGRAM Spanish Language Safety Training Videos for Loan! Located on the OSHA Website http://www.osha.gov/fso/ote/training/resource-center/loan.html Or contact the Resource
More informationLIEBERT ITA2 MBC Quick-Start Guide 60Hz, 208V, 8-10kVA, Three-Phase
LIEBERT ITA2 MBC Quick-Start Guide 60Hz, 208V, 8-10kVA, Three-Phase The complete Liebert ITA2 MBC user manual is available at Vertiv s Web site, www.vertivco.com/en-us/products-catalog/critical-power/uninterruptible-powersupplies-ups/
More informationPortable Hand and Power Tools Self-Inspection Checklist
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Portable Hand and Power Tools Self-Inspection Checklist Guidelines: This checklist covers
More informationMartin ApronSeal Skirting
Martin ApronSeal Skirting Go to Martin ApronSeal Skirting web page Operator s Manual M3248 Important MARTIN ENGINEERING HEREBY DISCLAIMS ANY LIABILITY FOR: DAMAGE DUE TO CONTAMINATION OF THE MATERIAL;
More informationInstallation Manual. Fortress OSHA Stair System Adjustable Temporary Stair Rated Load: 100 psf, 300 lbs. concentrated. 3-Tread at 25.
Installation Manual Fortress OSHA Stair System Adjustable Temporary Stair Rated Load: 100 psf, 300 lbs. concentrated 3-Tread at 25.5 3-Tread at 34 4-Tread at 34 4-Tread at 42.5 Manufactured in the USA
More informationduaro Safety Manual Kawasaki Heavy Industries, Ltd DEA
Safety Manual Kawasaki Heavy Industries, Ltd. 90801-1009DEA PREFACE This manual describes precautions and rules for safety when using Kawasaki duaro robot, the dual-arm SCARA robot. Read and fully understand
More informationBaxter Safety and Compliance Overview
Baxter Safety and Compliance Overview How this unique collaborative robot safely manages operational risks Unlike typical industrial robots that operate behind safeguarding, Baxter, the collaborative robot
More informationMAC000-HBK-ENG
Machine Guarding MAC000-HBK-ENG-0000 www.coastal.com 04-2001 Machine Guarding This employee handbook is one of a series of fully-illustrated employee handbooks, informative posters, broadcast-quality video
More informationMANUAL METAL SHRINKER/STRETCHER
MANUAL METAL SHRINKER/STRETCHER Model 95062 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,
More informationTech. Services: (800) Fax: (800) Order Entry: (800) Fax: (800) NUT SPLITTER. Max.
SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Internet Address: http://www.powerteam.com Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031
More informationElectrical Severity Measurement Tool Revision 4
Electrical Severity Measurement Tool Revision 4 November 2017 Electrical Severity Measurement Tool 1.0 Purpose: This tool is intended to measure the severity of exposure to an electrical safety event based
More information[Note to PSC: Include these sections in the Contract Documents, even though some are not included in the U of I Facilities Standards]
SECTION 01 78 23 - OPERATION AND MAINTENANCE DATA PART I - GENERAL 1.1 SUMMARY A. Operation and Maintenance Data shall be submitted in appropriately-sized binders, with dividers, and organized by each
More informationOperations Manual. Serial Number: Original Instructions - IW7503
Operations Manual Serial Number: Original Instructions - IW7503 Operations Manual 1 General Declarations of Conformity Company Profile Warranty Machine Identification Operator and Supervisor Information
More informationBy: Georgia Institute of Technology
Date: / / Page 1 of 19 1.0 PURPOSE 2.0 SCOPE To provide instructions for the registration, use, operation, control, and accountability of radiation machines at the Georgia Institute of Technology (Georgia
More informationCNC Production Mill-Operation
Course Outcome Summary 31420315 CNC Production Mill-Operation Course Information Description: Career Cluster: Instructional Level: Total Credits: 1.00 Total Hours: 36.00 Operation of CNC (Computer Numerical
More informationJARVIS. Model25CL-4,5,6 Hock Cutter and Loin Dropper. 25CL--5 Front Legs and Horns. 25CL--4 Hind Legs and Horns. 25CL--6 Loins
Model25CL-4,5,6 Hock Cutter and Loin Dropper 25CL--4 Hind Legs and Horns 25CL--5 Front Legs and Horns 25CL--6 Loins EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page 25CL--4... 4025007 25CL--5...
More informationMECHANICAL MAINTENANCE SKILLS
MECHANICAL MAINTENANCE SKILLS COURSE 700: 5 DAYS: Max 4 Candidates This course provides personnel with the necessary skills to perform mechanical maintenance, including the removal and replacement of equipment
More informationAgilent 5DX Series 2L, 3, and 5000 X-ray Safety Test Report
Agilent 5DX Series 2L, 3, and 5000 X-ray Safety Test Report To be completed by the EMG RADIATION SAFETY & REGULATORY ENGINEER: System SN: Test Date: Month Day Year Survey Report Type: Net X-ray emission:
More informationAgilent 5DX System. X-ray Safety Test Procedure. for use with Software Release 8.20 and later
Agilent 5DX System for use with Software Release 8.20 and later Agilent Technologies, Inc. 1996-2008 Agilent Safety and Regulatory Information: Restricted Rights Notice If software is for use in the performance
More informationHazardous Equipment Posters
Hazardous Equipment Posters Grain Augers and Hazards A grain auger is used to put grain into a grain bin or transport grain out of the bin to a truck or grain wagon to take to market. This grain auger
More informationTitle Operating Work - Low Voltage Distribution System. Reference Number POP 06 - (RIC Standard: EP SI)
Discipline Engineering Standard - NSW Category Electrical Title Operating Work - Low Voltage Distribution System Reference Number POP 06 - (RIC Standard: EP 95 30 00 03 SI) Document Control Status Date
More informationEducation & Training
Distribution System Operator Certificate This program provides you with a proficient working knowledge in modern electric power distribution systems. These four classes are designed to walk students through
More informationPREFACE ********************************************************** IT IS NOT INTENDED THAT THESE STANDARDS BE COPIED AND USED AS A SPECIFICATION!
PREFACE This publication has been prepared as a guide for Architectural and Engineering (A&E) firms in the preparation of documents for the design and construction of new structures and the remodeling
More informationSINGLE PHASE BUCK & BOOST TRANSFORMERS INSTRUCTION MANUAL
SINGLE PHASE INSTRUCTION MANUAL DIAGRAM D This manual applies to all single-phase buck & boost transformers sold by Larson Electronics. Please refer to the connection diagram on pages 4-6 for properly
More informationMinnesota Rules, Chapter 4732 X-ray Revision
Minnesota Rules, Chapter 4732 X-ray Revision PROPOSED DRAFT BOMB DETECTION X-RAY SYSTEMS, 1.0 4732.#### BOMB DETECTION X-RAY SYSTEMS. Subpart 1. Applicability. A registrant s bomb detection x-ray system
More informationTimken Bearing. maintenance Training
Timken Bearing maintenance Training Timken Bearing MAINTENANCE TRAINING HELPING IMPROVE BEARING PERFORMANCE Timken is where customers turn to increase the performance and uptime of their equipment. That
More informationSECTION ELECTRICAL IDENTIFICATION
SECTION 16075 ELECTRICAL IDENTIFICATION PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationDesign of an Intelligent Tool for the Observation and Follow-Up of Lockout Procedures during Maintenance Activities on Industrial Machines
Open Journal of Safety Science and Technology, 2014, 4, 106-118 Published Online June 2014 in SciRes. http://www.scirp.org/journal/ojsst http://dx.doi.org/10.4236/ojsst.2014.42012 Design of an Intelligent
More informationSWITCHING SAFETY & RELIABILITY CONFERENCE
SWITCHING SAFETY & RELIABILITY CONFERENCE JARGON WORKSHEET Energize (v) Energize is the process of applying rated voltage to circuit or equipment. Modified IEEE or OSHA from Adj. to verb. To make a piece
More informationNFPA-70E. Electrical Safety in the Workplace. Standard for Edition
NFPA-70E Standard for Electrical Safety in the Workplace 2015 Edition NFPA-70E 90.1 Purpose. The purpose of this standard is to provide a practical safe working area for employees relative to the hazards
More informationHeating Ventilating Air Conditioning - Refrigeration COURSE SYLLABUS
Heating Ventilating Air Conditioning - Refrigeration COURSE SYLLABUS 2017-2018 Course Description The Heating, Ventilation, Air Conditioning and Refrigeration (HVACR) Technology program provides a balance
More informationElectrical Switchgear & Power Transformer Testing. H.H. Sheik Sultan Tower (0) Floor Corniche Street Abu Dhabi U.A.E
Electrical Switchgear & Power Transformer Testing H.H. Sheik Sultan Tower (0) Floor Corniche Street Abu Dhabi U.A.E www.ictd.ae ictd@ictd.ae Course Introduction: This will provide you with practical knowledge
More informationEFCOG BEST PRACTICE # 211. Best Practice Title: Managing Hazards of Multiwire Branch Circuits Installed Before the 2008 NEC
EFCOG BEST PRACTICE # 211 Best Practice Title: Managing Hazards of Multiwire Branch Circuits Installed Before the 2008 NEC Facility: DOE Complex Point of Contact: John (Jackie) McAlhaney, Savannah River
More informationStudio Equipment. Safe Operating Procedures. Metal Studio. Office of Safety & Risk Management Rosalie Sharpe Pavilion 115 McCaul Room 2210
Studio Equipment Safe Operating Procedures Metal Studio Office of Safety & Risk Management Rosalie Sharpe Pavilion 115 McCaul Room 2210 ------------------------- This page intentionally left blank ---------------------------
More informationOKI B721/B731/MPS5501 Printer Important Information Update
OKI B721/B731/MPS5501 Printer Important Information Update 543 Toner Sensor Error after installing a new or replacement print cartridge into the printer. Check the print cartridge for the following problem
More informationNUT SPLITTER. Max. Capacity: 15 Ton
Form No. 1000446 Parts List and Operating Instructions for: HNS150-TCC NUT SPLITTER Max. Capacity: 15 Ton NOTE: For a detailed parts list or to locate a Power Team Authorized Hydraulic Service Center,
More informationValley AutoPilot Control Panel Owner's Manual
Valley AutoPilot Control Panel Owner's Manual For Software Version 2.00 0998901_B 2015 Valmont Industries, Inc., Valley, NE 68064 USA. All rights reserved. www.valleyirrigation.com 2 Valley AutoPilot Control
More informationSection 16621A - AUTOMATIC TRANSFER SWITCH. Part 1 General
Section 16621A - AUTOMATIC TRANSFER SWITCH Part 1 General 1.01 One 600 Amp, 3 Phase, 480 Volt Automatic Transfer Switch (ATS) shall be provided with gasketed enclosure. The ATS shall consist of an inherently
More informationNo. SSIEC-SEW SHINSUNG. Solid Insulation Eco Load Break Switch (SILO) SILO SERIES 15kV, 27kV 400A, 630A
SHINSUNG Solid Insulation Eco Load Break Switch (SILO) SILO SERIES 15kV, 27kV 400A, 630A Enhanced Self Healing System General SILO is 3 phase, solid insulated load break switch (LBS) and vacuum interruption
More informationSource 2018 COURSE SCHEDULE SGT. MAJ. PHIL FASCETTI GIVES BACK UC SAN DIEGO EXTENSION CELEBRATES 25 YEARS OF MAKING SAFER WORK SPACES SAFETY FEST
SAFETY Source S AV I N G L I V E S W I T H W O R K F O R C E E D U C AT I O N, P R E PA R AT I O N & A W A R E N E S S Est. 1992 UC SAN DIEGO EXTENSION CELEBRATES 25 YEARS OF MAKING SAFER WORK SPACES SAFETY
More informationEllington Industrial Supply, Inc. P. O. Box 128 Ellington, Missouri USA Web site:
Baker Edger/Mini-Scragg User Manual Ellington Industrial Supply, Inc. P. O. Box 128 Ellington, Missouri 63638 USA Web site: www.baker-online.com E-mail: info@baker-online.com Phone: (573) 663 7711 Fax:
More information(SHOP NAME) Shop Safety Plan
(SHOP NAME) Shop Safety Plan i SHOP SAFETY PLAN TABLE OF CONTENTS 1.0 STATEMENT OF PURPOSE... 2 2.0 GENERAL SHOP INFORMATION... 3 3.0 SHOP POLICIES AND PROCEDURES... 4 4.0 INVENTORY OF SHOP EQUIPMENT...
More informationTABLE OF CONTENTS. References
ANALYTICAL X-RAY EQUIPMENT USE POLICIES & PROCEDURES Page 1 of 9 Revised: 11/24/2003 TABLE OF CONTENTS 1.0 General 2.0 Purpose 3.0 Scope and Authority 4.0 Equipment Requirements 4.0.1 Safety device 4.0.2
More informationType XTSR71 Sizes
(Page 1 of 13) s 494-5258 Type XTSR71 s 494-5258 Figure 1 Thomas XTSR71 Coupling 1. General Information 1.1 Thomas Couplings are designed to provide a mechanical connection between the rotating shafts
More informationHilti, Inc. November Dallas Parkway, Suite 1000 Plano, Texas Toll Free Website Guide Specification
Hilti, Inc. November 2015 7250 Dallas Parkway, Suite 1000 Plano, Texas 75024 Toll Free 800-879-8000 Website www.us.hilti.com Guide Specification Specifier Notes: This guide specification is written in
More informationNational Institute for Metalworking Skills
National Institute for Metalworking Skills DUTIES AND STANDARDS FOR INDUSTRIAL MAINTENANCE TECHNICIANS (MECHATRONICS TECHNICIANS) Level I TABLE OF CONTENTS Introduction... 4 Acknowledgements... 5 I. Duty
More informationCertified Precision Sheet Metal Operator Level I
Certified Precision Sheet Metal Operator Level I 13 Sections Total of 136 tasks/skills/knowledge areas Section B. Metals, Metallurgy, and Metal Working Processes Section C. Paperwork and Documentation
More informationMini Max 20 BAND SAW
OPERATING PROCEDURE FOR: Mini Max 20 BAND SAW SAFETY RULES: Warning: Willful violations of these safety rules, disruptive actions or horseplay may result in loss of the privilege to use the tools and machinery
More informationLOS ANGELES UNIFIED SCHOOL DISTRICT DIVISION OF ADULT AND CAREER EDUCATION SAFETY TEST FOR MACHINIST PROGRAM
LOS ANGELES UNIFIED SCHOOL DISTRICT DIVISION OF ADULT AND CAREER EDUCATION SAFETY TEST FOR MACHINIST PROGRAM School: Industry Sector: Manufacturing & Product Dev. Class: Date: Teacher: Room: (Please Print)
More informationFLAVESCO ELEVATOR GUARDING USER MANUAL
FLAVESCO ELEVATOR GUARDING USER MANUAL QMF 19 Rev 4.0 May 24 th 2013 WARNINGS GUARDING CAN BE INSTALLED AND REMOVED ONLY BY CERTIFIED ELEVATOR MECHANICS. MACHINE MUST BE SHUT DOWN AND LOCKED OUT BEFORE
More informationTable of Contents. Quick Start Guide. Important Notes! Nautilus GPS Components. Operation. Region Programming & MMSI. Nautilus GPS App.
Table of Contents 03 04 05 06 07 08 09 09 10 10 11 Quick Start Guide Important Notes! Nautilus GPS Components Operation Region Programming & MMSI Nautilus GPS App Test Sequence Maintenance Battery Information
More informationTAG5000 WIRELESS PHASER. Instruction Manual HD ELECTRIC COMPANY 1475 LAKESIDE DRIVE WAUKEGAN, ILLINOIS U.S.A.
TAG5000 WIRELESS PHASER Instruction Manual TM HD ELECTRIC COMPANY 1475 LAKESIDE DRIVE WAUKEGAN, ILLINOIS 60085 U.S.A. PHONE 847.473.4980 FAX 847.473.4981 website: www.hdelectriccompany.com DESCRIPTION
More informationProgramme-Based Engagement
Programme-Based Engagement Contents 1. Introduction 03 2. Understanding Hand and Finger Amputations Caused by Machines 03 3. Machines Commonly Involved in Hand and Finger Amputations 04 4. What Must be
More informationINTERIM ARRANGEMENTS FOR GRID TIED DISTRIBUTED ENERGY RESOURCES. Technical Requirements for Grid-Tied DERs
INTERIM ARRANGEMENTS FOR GRID TIED DISTRIBUTED ENERGY RESOURCES Technical Requirements for Grid-Tied DERs Projects Division 6/29/2017 Contents 1 Definitions and Acronyms... 1 2 Technical Interconnection
More informationXLTX and MLTX2 Transmitters
XLTX and MLTX2 Transmitters Radio Control Equipment Instruction Manual Part Number: 198-00144-0009 R0 Copyright 2018 Magnetek Material Handling Page Intentionally Left Blank Page 2 of 57 Table of Contents
More informationPredictive Diagnostics for Pump Seals: Field Trial Learnings. Matthew Miller, John Crane
Predictive Diagnostics for Pump Seals: Field Trial Learnings Matthew Miller, John Crane Brad D. Lewis Senior Reliability Engineer Authors Bios Matthew Miller Field Service Engineer At INEOS from 2014-2016
More informationNZQA registered unit standard version 2 Page 1 of 8. Demonstrate knowledge of theory for registration of electrical installers
Page 1 of 8 Title Demonstrate knowledge of theory for registration of electrical installers Level 3 Credits 3 Purpose This unit standard covers the theory assessment required for registration as an electrical
More informationMaintenance Manual Original Instructions - IW6004
Maintenance Manual Original Instructions - IW6004 Maintenance Manual 1 General Operator and Supervisor Information Signal Word Definition Signal Word Panel 2 Maintenance Precautions Maintenance Schedule
More informationApplying Robotic Technologies to Improve Manufacturing Processes
Applying Robotic Technologies to Improve Manufacturing Processes CrossRobotics.com What Can You Automate? Use Our Expertise to Configure Your Entire Robotic Cell If you ve always thought robotic automation
More informationMachine Shop Policy. Policy Number: 2.7 Supersedes: Policy of December 12, 2011 Implementation Date: January 18, 2017
Policy Number: 2.7 Supersedes: Policy of December 12, 2011 Implementation Date: January 18, 2017 Machine Shop Policy Index: Introduction:... 1 Section A: Shop Organization and Current Resources... 2 1.0
More informationTable of Contents. Quick start guide. Important! Get to know Nautilus GPS. Operation MMSI. Test sequence. Maintenance. Battery Information
Table of Contents 03 04 05 06 07 08 08 09 09 10 Quick start guide Important! Get to know Nautilus GPS Operation MMSI Test sequence Maintenance Battery Information Rewinding Antenna Specifications QUICK
More informationSUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches
SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches PART 1 GENERAL 1.01 Scope Furnish and install automatic transfer switches (ATS) with number of poles, amperage, voltage, and withstand
More information