NECESSITY IS THE MOTHER OF INVENTION I. INTRODUCTION

Size: px
Start display at page:

Download "NECESSITY IS THE MOTHER OF INVENTION I. INTRODUCTION"

Transcription

1 NECESSITY IS THE MOTHER OF INVENTION M. Leslie Boyd, P.E., Freese and Nichols, Inc Mike Lowe, P.E., Lower Colorado River Authority Dustin Mortensen, P.E., Freese and Nichols, Inc. I. INTRODUCTION When Buchanan Dam was constructed in 1938, there was no tainter gate dewatering system provided. Thus, routine maintenance occurred primarily when low reservoir levels exposed the entire gate face. At such times, gates could be exercised, painted and repaired. The only problem was that you had more than thirty gates to deal with and even small maintenance issues became complex because you never knew when the lake would suddenly rise. This caused the premature and unwanted termination of gate painting and chain replacement on at least two occasions. The termination of chain replacement efforts resulted in the hiring of divers to complete the unfinished work underwater and at a greatly increased cost. This made it very clear that a dependable and easy to install dewatering system was no longer a luxury but, much more so, a necessity. Also, the tainter gates had been evaluated and recommended for gate strengthening. There was no way the Owner could embark on such a major undertaking without a viable gate dewatering system. The Lower Colorado River Authority (LCRA) is the above referenced Owner of Buchanan Dam. Once the LCRA made the decision to authorize the development and design of dewatering systems, they also concluded that the system should be deployable in an emergency situation. That is, the system should be deployable in flowing water in the event of a gate failure or a gate malfunction. This decision was based on the value of the water which would be lost if the gate failure emptied the lake down to the gate sill elevation. They concluded that this occurrence is not unreasonable, having witnessed the problems subsequent to the Folsom Dam gate failure a few years ago. Since no system for dewatering a tainter gate in emergency flowing water existed to our knowledge, we embarked upon a very unique and challenging assignment. This is why you have to love engineering. A. History II. BACKGROUND Buchanan Dam was constructed approximately seventy years ago by the LCRA. Again, the original design did not include any tainter gate dewatering system, very likely because the designers deemed it reasonable to draw the lake down in order to perform maintenance on the gates or expected to do maintenance when the reservoir was low. In that period of time that was not an unreasonable expectation because there were very few people in the area and small water demands. However, today, with almost a million people dependent upon LCRA s water supply, the idea of wasting water for maintenance endeavors is essentially unthinkable.

2 B. Project Description Buchanan Dam is the uppermost of six dams located on the Colorado River in Texas. The system of six dams and reservoirs is collectively known as the Highland Lakes. Buchanan Dam is located near Burnet, Texas and approximately 100 river miles upstream of Austin, Texas. The dam is one of the largest multiple arch dams in the United States. It has a length of two miles and a maximum height of approximately 145 feet. The dam has three gated spillways which contain a total of thirty-seven tainter gates. The LCRA has been able to exercise/maintain these gates only during flood events or during periods of extremely low reservoir elevations. The gates have performed very well over the past seven decades but have been identified as needing some minor structural modifications to their framework to bring them into compliance with present day standards of performance. Thirty of the gates are referred to as the small gates and they are 33 feet wide and 15 feet high. There are 16 such gates in the northernmost spillway and 14 such gates in the middle spillway. The other seven gates are housed in the spillway just north of the powerhouse and are referred to as the large gates. They are 40 feet wide and 25 feet high. The large gates are also scheduled for a dewatering system but will not be discussed further within this paper. Buchanan reservoir is operated at two different normal pool levels depending on the season of the year. The two elevations (msl) are 1020 for winter/spring operation and 1018 for summer/fall operation (hurricane season). The crest elevation for the small gates is at The loss of stored water from elevation 1020 or 1018 down to elevation 1005 is 301,000 acre feet and 257,000 acre feet, respectively. LCRA recognizes this potential loss of volume due to a gate fault as unacceptable and thus stood firmly behind their desire to have a dewatering system capable of emergency deployment as well as an operator friendly routine maintenance system. LCRA contracted with Freese and Nichols, Inc. (FNI) in June 2009 to develop a dewatering system for all three spillways at Buchanan Dam. A. Background III. PROJECT APPROACH A preliminary evaluation of spillway gate dewatering options was performed in June 2007 by FNI. This report had studied typical stop logs, sheetpile bulkheads, horizontal floating bulkheads, and barn-door type sliding bulkheads for the small gates. Figure 1 taken from that report and included herein, also as Figure 1, presents the 2007 recommended typical stop log concept. The figure illustrates the geometric relationship wherein the pier sets forward of the concrete crest and a sealing apron is proposed for construction in order to provide a bottom sealing surface for the stop logs. Figure 1 also illustrates that the existing pier would need to be extended upstream to provide room for a stop log slot. The existing piers are only four feet wide and it was opined that cutting stop log slots in such a narrow pier without the ability to reinforce the existing concrete was too risky. Thus, the pier was recommended for an upstream extension. Each of the other options studied in the 2007 Report also required the construction of a concrete apron immediately upstream of each gate crest to provide a bottom sealing surface for their systems. None of the studied systems in the 2007 Report for the small gates were capable of being installed in an emergency situation of flowing water. However,

3 the information contained in this earlier report provided some good information for now attacking the design of a system capable of being installed in flowing water. Figure 1. Previous Report Concept

4 Subsequent to the 2007 Report, gate rating curves were developed as part of a hoist study wherein LCRA was determining whether they could react quickly enough to a rain bomb which might occur quickly and very near the dam. The study evaluated reaction time and the necessary number of hoists required for the 37 gates at Buchanan Dam. However, the part of the study which was determined relevant to our new dewatering design was the gate discharge ratings which were developed. The ratings were developed using computational fluid dynamic (CFD) models. The ratings which included shallow approach similar to the aprons proposed in the 2007 study indicated an unacceptable level of gate discharge reduction. Thus, we were challenged to approach any new dewatering design with either lower aprons or none at all. The LCRA has dewatering systems at some of their other dams along the Colorado River and they relayed some of their problem issues and criticism of the dewatering systems. These included needing divers for routine installation of stop logs and the difficulties associated with latching and un-latching lifting beams under water. On more than one occasion, the lifting beam and its attached stop log had been partially dropped on one end and required significant time and expense to rectify and retrieve the system components. The LCRA thus conveyed their desire for a system simple enough to install without divers or cranes, and with an improved lifting beam to be more user friendly and safe. B. Dewatering System Based upon our acknowledgement of the above described matters and from a cursory review of several documents in the technical literature mentioning emergency dewatering systems, we developed the following list of desirable/necessary features for a dewatering system for the small gates at Buchanan Dam: Must be deployable in flowing water Should be easy to install Should have a simple lifting beam system Should be deployable at any reservoir elevation, i.e. at or below normal pool Should not require an approach apron Should not significantly reduce discharge capacity of the gated spillways Must be readily deployable by LCRA without divers or cranes or transport by others Should not induce any significant hydraulic loads resulting in abnormal hoist function The preliminary dewatering system developed by the FNI team is shown on Figure 2. The following key points are presented: The curved track is mounted to the pier face and negates the need for any upstream apron The bottom stop log will seal against an existing concrete surface on the crest The logs will be hinged and traverse the curved track using two wheels on each end Each stop log will be its own lifting beam Each log will be lifted by the upper axle located at each end of the log

5 Any log can support the entire assemblage The entire system will be assembled one log at a time in the bay to be dewatered A dogging system will be used to allow the stacking procedure and free the hoist for transporting each log bay-to-bay The bottom log is special, all other logs are interchangeable All horizontal travel (bay-to-bay) will be with only one log All heavy lifts will be made near each pier to minimize cantilevered loading The top log will never be subjected to flows over its top surface Figure 2. Present Concept

6 Horizontal joints will be sealed with flap seals to prevent abnormal forces during emergency deployment Each end of each log will be sealed with vertical flap seals Being a tube sealed on the ends, each log through the simple addition of threaded inlets can allow water ballast to be added in the event more weight becomes necessary to seat the system The FNI team had confidence in the design developed above but advised LCRA that only a model test could prove its effectiveness in flowing water and provide data on any abnormal hydraulic forces or phenomenon. LCRA concurred and the modeling skills of Utah Water Research Laboratory (UWRL) were engaged. A. The Model IV. HYDRAULIC MODEL STUDY FNI developed preliminary concept drawings to a level of detail where UWRL could construct the hydraulic model components necessary for the study. The UWRL model team was led by Mike Johnson, P.E. The following is a very brief summary of the extensive efforts provided by UWRL on this investigation and is not intended to be a complete or allinclusive presentation. UWRL selected a model scale of 1:16.5 and determined that a Froude model was appropriate for the items needing study. UWRL constructed a gate and spillway model in the flume of their research facility in Logan, Utah. Figure 3 is a photograph of the spillway model and flume. The key issues presented for study were: Could the system be deployed in flowing water What pier nose modification provided acceptable hydraulic flow What effect would the tracks mounted on the vertical pier face have on discharge capacity What, if any, hydraulic phenomenon or forces were occurring on the stop logs What loads would be imparted to the lifting mechanisms (cables) UWRL had the stop logs machined from aluminum and duplicated the hinging and wheel system very thoroughly. Weights were also controlled to the proper model ratio by machining out the cavity within each log until the appropriate weight was obtained. A typical log is shown in Figure 4. The rubber seals were simulated using thin rubber strips. Load cells were placed on each lifting cable to measure the loads. The entire system was monitored with computers to provide real time output which was stored for future reference.

7 Figure 3. Spillway Flume Model Figure 4. Typical Log Model

8 B. The Testing The testing first proceeded with the various pier nose shapes presented for study. A half round pier nose and a blunt nose with ellipses were evaluated. The new pier shapes were found to produce very close to the same discharge. The FNI design team then chose the blunt nose with ellipses as being the one for future investigation. This shape provided more flat sealing surface area for the proposed vertical side seals. Both nose shapes were evaluated with the surface mounted track installed. It was determined that the reduction in discharge was only 1 to 2 percent. UWRL then performed a series of tests installing the stop logs at various reservoir elevations in both still and flowing water. LCRA and FNI witnessed some of the final testing of the system during a visit to the laboratory in October During this visit, a partially blocked gate was simulated (Figure 5) and the system was observed as performing very well in several emergency simulation deployments. Figure 5. Partially Blocked Gate

9 C. The Results The UWRL model study was a resounding success and indicated the proposed system was viable for Buchanan Dam s small gates. A complete Hydraulic Model Study Report has been prepared by UWRL and affords a much more detailed look at the system. However for the purpose of this paper, the significant findings are: The curved track system is viable in both still and flowing water. The reduction in flow capacity caused by the projecting tracks is minimal. There is no noted hydraulic phenomenon causing adverse conditions. A small jump was noted occurring on the downstream apron for just a few moments before the bottom log fully seated. The maximum load on each lifting cable was approximately 37,000 pounds and this corresponds essentially with the dead weight of the stop log system. V. CONCLUSION We believe the preliminary dewatering system developed for the 33 feet by 15 feet gates at Buchanan dam present a viable dewatering system both for routine installation and for deployment in flowing water emergency situations. We believe the system has key features which support its ease of use: first, with the innovative approach to the lifting beam inclusion into each stop log, and second with the articulating logs on a curved track. Further, this may well be one of the first dewatering systems for a tainter gate spillway suitable for emergency deployment.

Pioneers in Gate Design

Pioneers in Gate Design Stop Logs Pioneers in Gate Design Hydro Gate 3888 E. 45th Ave. #120 Denver, CO 80216 Your Source for Water Control Gates No matter what type of gates your project demands, chances are excellent Hydro Gate

More information

3.2 Structures in Small Lined Canals

3.2 Structures in Small Lined Canals Weirs with a partition board - The flow divisor consists essentially of a broadcrested weir with rectangular control section and a partition board downstream from the crest. The partition board may be

More information

Log Hauler. Senior Design Project. Department of Mechanical Engineering Trevor Kline 4/19/2011

Log Hauler. Senior Design Project. Department of Mechanical Engineering Trevor Kline 4/19/2011 Log Hauler Senior Design Project Department of Mechanical Engineering Trevor Kline 4/19/2011 Table of Contents BACKGROUND:... 3 INSPIRATION:... 3 PROPOSAL AND REQUIREMENTS:... 4 DESIGN:... 4 LOG SIZE:...

More information

Peace Project Water Use Plan. Physical Works Terms of Reference. GMSWORKS-26 Communications and Safety Improvements Williston, Dinosaur and Peace

Peace Project Water Use Plan. Physical Works Terms of Reference. GMSWORKS-26 Communications and Safety Improvements Williston, Dinosaur and Peace Peace Project Water Use Plan Physical Works Terms of Reference GMSWORKS-26 Communications and Safety Improvements Williston, Dinosaur and Peace April 21, 2008 Peace Water Use Plan Physical Works Terms

More information

PENSTOCK VALVES. Performance through Excellence

PENSTOCK VALVES. Performance through Excellence VALVES & MANUFACTURING (1988) LTD. PENSTOCK VALVES Performance through Excellence SLIDEGATES WEIR GATES STOP LOGS SLIDEGATES PRECISION FACE SEALING VALVES WEIR GATES STOP LOGS SLIDEGATES Actuation Installation

More information

XAYABURI HYDROELECTRIC POWER PROJECT. Fish Migration Facilities Vientiane, 15 July 2015 Dr Tobias Coe

XAYABURI HYDROELECTRIC POWER PROJECT. Fish Migration Facilities Vientiane, 15 July 2015 Dr Tobias Coe XAYABURI HYDROELECTRIC POWER PROJECT Fish Migration Facilities Vientiane, 15 July 2015 Dr Tobias Coe CHAPTER SLIDE, IMAGE ARIAL BOLD 30 PT, CAPITALS CONTENT OF PRESENTATION General issues at Xayaburi Data

More information

PART XIII: HYDRAULIC/ HYDROLOGY SURVEYS

PART XIII: HYDRAULIC/ HYDROLOGY SURVEYS PART XIII: HYDRAULIC/ HYDROLOGY SURVEYS 13.1 Purpose and Scope Hydraulic surveys are required for flow analysis to determine bridge and culvert design characteristics. A hydraulic survey is usually but

More information

ATTACHMENT H TACOMA HYDROELECTRIC PROJECT DESCRIPTION OF PROJECT FEATURES

ATTACHMENT H TACOMA HYDROELECTRIC PROJECT DESCRIPTION OF PROJECT FEATURES ATTACHMENT H TACOMA HYDROELECTRIC PROJECT DESCRIPTION OF PROJECT FEATURES The Tacoma Hydroelectric Project is located about 20 miles north of Durango, Colorado, on a high intermountain plateau west of

More information

QUALITY THROUGH EXPERIENCE-SINCE 1963

QUALITY THROUGH EXPERIENCE-SINCE 1963 b y H a k o h a v V a l v e s P E N S T O C K S & F L A P V A L V E S by Hakohav Valves ABOUT US QUALITY RELIABILITY Kim Valves started up as Hakohav Valves in 1963 by two young visionary engineers who

More information

SECTION SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES

SECTION SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES SECTION 01334 SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES PART 1 GENERAL 1.01 SUMMARY A. Submit to the ENGINEER for review, such working drawings, shop drawings, test reports and data on materials and equipment

More information

W X 12 SOLARIUM ASSEMBLY INSTRUCTIONS Two or more adults required for assembly

W X 12 SOLARIUM ASSEMBLY INSTRUCTIONS Two or more adults required for assembly adlonco@hotmail.com W07-3 8 X SOLARIUM ASSEMBLY INSTRUCTIONS Two or more adults required for assembly Requires 96 clearance at the wall Base Dimensions x 9 /, Largest Dimensions x98 / (see pg.) ZZZ-87.W07-3.7-5.GP.EN.HER.doc

More information

W1610 1/ X 16 SOLARIUM ASSEMBLY INSTRUCTIONS Two or more adults required for assembly

W1610 1/ X 16 SOLARIUM ASSEMBLY INSTRUCTIONS Two or more adults required for assembly adlonco@hotmail.com W60 /-3 0 X 6 SOLARIUM ASSEMBLY INSTRUCTIONS Two or more adults required for assembly Requires 96 clearance at the wall Base Dimensions 90 x 8, Largest Dimensions 90 x (see pg.4) ZZZ-0.W60-3.4-5.GP.EN.HER.doc

More information

SECTION 100 PRELIMINARY CONSIDERATIONS & INSTRUCTIONS

SECTION 100 PRELIMINARY CONSIDERATIONS & INSTRUCTIONS SECTION 100 PRELIMINARY CONSIDERATIONS & INSTRUCTIONS 101 General 102 Submittal Requirements A. Initial Submittal B. Second Submittal 103 Plan Requirements A. Subdivisions B. Site Plans 104 Approval of

More information

Stop Gates & Stop Logs. Series 500. ine. Manufacturing high quality gates since 1977

Stop Gates & Stop Logs. Series 500. ine. Manufacturing high quality gates since 1977 Stop Gates & Stop Logs Series 500 Manufacturing high quality gates since 1977 ine Stop Gates & Stop Logs Series 500 Contents Stop Gate Introduction 3 Model 501 3 Model 503 4 Model 503-C 4 Stop Gate Specification

More information

W1610 1/2 10 X 16 SOLARIUM ASSEMBLY INSTRUCTIONS Assembly by more than one person is suggested.

W1610 1/2 10 X 16 SOLARIUM ASSEMBLY INSTRUCTIONS Assembly by more than one person is suggested. adlonco@hotmail.com W60 / 0 X 6 SOLARIUM ASSEMBLY INSTRUCTIONS Assembly by more than one person is suggested. Requires 96 clearance at the wall Base Dimensions 90 x 8, Largest Dimensions 90 x (see pg.3)

More information

Glulam Connection Details

Glulam Connection Details T E C H N I C A L N O T E Glulam Connection Details Note: This version is superseded by a more current edition. Check the current edition for updated design and application recommendations. ENGINEERED

More information

Swivel Sector Radial Penstock

Swivel Sector Radial Penstock Swivel Sector Radial Penstock 24/03/2015 - TAINTOR type radial penstock. - Mechanically welded stopboard with sectoral shape, fitted with side wheels to guarantee correct guiding of the penstock throughout

More information

Precast Bridge. in only Eight Days. profile. Minimizing construction-related traffic delays and improving workzone

Precast Bridge. in only Eight Days. profile. Minimizing construction-related traffic delays and improving workzone Precast Bridge Built in only Eight Days by Peter E. Stamnas and Mark D. Whittemore. New Hampshire Department of Transportation Minimizing construction-related traffic delays and improving workzone safety

More information

VALVES AND PENSTOCKS FOR WATER

VALVES AND PENSTOCKS FOR WATER VALVES AND PENSTOCKS FOR WATER www.cmo.es Our COMPANY CMO is a company dedicated to the design, manufacture and assembly of standard and special valves and penstocks. Its extensive manufacture range allows

More information

TO: FROM SUBJECT: SRBA Jon Albright Technical Memorandum on Hydrologic Yields PROJECT: Sulphur River Basin Feasibility Study DATE: 08/26/2014 CC:

TO: FROM SUBJECT: SRBA Jon Albright Technical Memorandum on Hydrologic Yields PROJECT: Sulphur River Basin Feasibility Study DATE: 08/26/2014 CC: 593 Summerhill Rd Texarkana, Texas 7553 93-838-8533 fax 93-832-47 TO: FROM SUBJECT: PROJECT: SRBA Jon Albright Technical Memorandum on Hydrologic Yields Sulphur River Basin Feasibility Study DATE: 8/26/214

More information

GARDEN SHED BRIGHTOLN

GARDEN SHED BRIGHTOLN ASSEMBLY INSTRUCTIONS GARDEN SHED BRIGHTOLN Dimensions: 10x10 (1 1/8") IMPORTANT Before beginning the assembly of your garden shed, please read the instructions carefully and follow them closely. By doing

More information

Segmental Bridge Technology Established and Evolving. W. Jay Rohleder, Jr, P.E., S.E. Senior Vice President / Project Development FIGG

Segmental Bridge Technology Established and Evolving. W. Jay Rohleder, Jr, P.E., S.E. Senior Vice President / Project Development FIGG 1 Segmental Bridge Technology Established and Evolving W. Jay Rohleder, Jr, P.E., S.E. Senior Vice President / Project Development FIGG 2 Segmental Bridge Topics Addressed Definition of concrete segmental

More information

Retractable Pool Cover

Retractable Pool Cover Retractable Pool Cover By: Abdulhadi Alkhaldi, Zachary Keller, Cody Maurice, Bradley Miller, and Patrick Weber Team 12 Midpoint Review Document Submitted towards partial fulfillment of the requirements

More information

SECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP

SECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP 1 1 1 0 1 0 1 0 1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of

More information

Choosing, Designing, & Building a Hydraulic Log/wood Splitter

Choosing, Designing, & Building a Hydraulic Log/wood Splitter Choosing, Designing, & Building a Hydraulic Log/wood Splitter Part 1 - "Deciding on what type of log/wood splitter will best fit your needs" - Covers 4 common styles of hydraulic log/wood splitter & pros/cons

More information

Micrometre-level Deformation Monitoring of a Concrete Dam

Micrometre-level Deformation Monitoring of a Concrete Dam ARTICLE ACCURATE AND FREQUENT DEFORMATION MONITORING USING FIBRE-OPTIC CABLES Micrometre-level Deformation Monitoring of a Concrete Dam Highly accurate measurements with a high temporal resolution have

More information

IMPORTANT - STATE AIRCRAFT REGISTRATION NUMBER IN ALL CORRESPONDENCE MOONEY AIRCRAFT, INC. M-l8 SERVICE LETTER NO.17

IMPORTANT - STATE AIRCRAFT REGISTRATION NUMBER IN ALL CORRESPONDENCE MOONEY AIRCRAFT, INC. M-l8 SERVICE LETTER NO.17 IMPORTANT - STATE AIRCRAFT REGISTRATION NUMBER IN ALL CORRESPONDENCE MOONEY AIRCRAFT, INC. M-l8 SERVICE LETTER NO.17 (This Service Letter is FAA. Approved) DATE: OCTOBER 24, 1959 SUBJECT: REAR BULKHEAD

More information

Helical Pile Foundation

Helical Pile Foundation Building a Boardwalk by Darren Tracey Heavy-duty framing supported by helical piles minimized environmental impact on a sensitive site Round Lake is located just north of Albany, N.Y., and is connected

More information

Jeep Cherokee 4-Door XJ Set Part # Rev

Jeep Cherokee 4-Door XJ Set Part # Rev Jeep Cherokee 4-Door XJ Set Part # 10911 Rev-14 04-05-10 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided.

More information

User s Manual For CT Model IMB

User s Manual For CT Model IMB User s Manual For CT Model IMB 2 of (13) Contents: A. Introduction... 3 B. Steps on receipt and opening the cases... 3 C. Transportation and handling... 3 D. Unpacking the transformer... 4 E. Storage...

More information

W1209 1/2 10 X 12 SOLARIUM ASSEMBLY INSTRUCTIONS

W1209 1/2 10 X 12 SOLARIUM ASSEMBLY INSTRUCTIONS W09 / 0 X SOLARIUM ASSEMBLY INSTRUCTIONS Assembly by more than one person is suggested. Base Dimensions x 8, Largest Dimensions x (see pg.3) L:\WP5\Instructions\SOLARIUMS INSTRUCTION BOOKS\W09\ZZZ-09.W09.GP.EN.doc

More information

1.0. Aluminum Prebuilt Fence. Owner's Manual. Version. For Home, Haven, Select & Premier Series. Installation Instructions

1.0. Aluminum Prebuilt Fence. Owner's Manual. Version. For Home, Haven, Select & Premier Series. Installation Instructions Owner's Manual Aluminum Prebuilt Fence Installation Instructions For Home, Haven, Select & Premier Series Version 1.0 ALUMFENCEA_BOM V1 2/12 PLEASE READ OWNER'S MANUAL COMPLETELY BEFORE ASSEMBLING YOUR

More information

INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS

INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS 2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed

More information

Metal Roof Installation Manual. Chapter 5: Panel Attributes/Profiles

Metal Roof Installation Manual. Chapter 5: Panel Attributes/Profiles Metal Roof Installation Manual Chapter 5: Panel Attributes/Profiles Chapter 5: Panel Attributes/Profiles Chapter Contents 5. Panel Attributes / Profiles... 5-1 5.1 Widths... 5-1 5.2 Ribs... 5-2 5.2.1 Rib

More information

WRS Artificial Lift System

WRS Artificial Lift System WRS Artificial Lift System Patent Pending Designed to adapt to any type of Artificial Lift Suspension! Artificial Lift and Down hole gauge monitoring Is fast Becoming the go to in the oil production market.

More information

Storefront Installation Guide

Storefront Installation Guide Storefront General Notes: 1. Check Contract Documents and Shop Drawings. Understand and clarify any Field Verify Notes and approvals of drawings and products to be familiar with the project. Installation

More information

Technical Memorandum ECO-7

Technical Memorandum ECO-7 To: Woody Frossard, TRWD From: Bob Brashear, CDM This document is released for the purpose of interim review under the authority of Robert Brashear, P.E., TX license 80771 on 21-Mar-2005. It is not to

More information

Total precast solution for large stadium projects meet tight schedule

Total precast solution for large stadium projects meet tight schedule Tailor Made Concrete Structures Walraven & Stoelhorst (eds) 2008 Taylor & Francis Group, London, ISBN 978-0-415-47535-8 Total precast solution for large stadium projects meet tight schedule T.J. D Arcy

More information

INSTALLATION INSTRUCTIONS for Custom and Premium Pocket Windows (JII022) IMPORTANT INFORMATION AND GLOSSARY SAFETY AND HANDLING

INSTALLATION INSTRUCTIONS for Custom and Premium Pocket Windows (JII022) IMPORTANT INFORMATION AND GLOSSARY SAFETY AND HANDLING Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to

More information

Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.

Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation. Installation Guide for E-Series/Eagle High-Performance Mullion Windows with LVL Reinforcement and Installed Using Type B Clips Thank you for choosing Andersen. Instructions are for typical, new wood-framed

More information

Vinyl compound blended with impact modifiers Creates a durable product that will not chip, crack, or peel.

Vinyl compound blended with impact modifiers Creates a durable product that will not chip, crack, or peel. Quality Vinyl Fencing with Step Down Pickets 51/2-6 h. Most vinyl fence and railing profiles appear the same, that is until you take a closer look. A closer inspection of fence and railing extrusions from

More information

OWNER S MANUAL STORAGE SHED MODELS: STOR-96-G-W-1RH & STOR-912-G-W-1RH

OWNER S MANUAL STORAGE SHED MODELS: STOR-96-G-W-1RH & STOR-912-G-W-1RH STORAGE SHED MODELS: STOR-96-G-W-1RH & STOR-912-G-W-1RH OWNER S MANUAL Introduction.. 1 Assembly Instructions STOR-96-G-W-1RH... 2 Assembly Instructions STOR-912-G-W-1RH... 8 STOR-96-G-W-1RH Exploded Parts

More information

WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS

WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS These instructions were tested developed for replacing windows in wood-frame wall construction systems

More information

D. Drill Bolt Holes Through Topper Shell and Bed Rails

D. Drill Bolt Holes Through Topper Shell and Bed Rails A. Check Mounting Kit Check to make sure that all of the following items are included in the mounting kit. Call 515-272-4372 if you need to obtain a part from BrandFX. Double-stick tape (1 roll) White

More information

Rattling Brook Hydro Plant Refurbishment. Table of Contents. 1.0 Introduction Background Electrical Works...7

Rattling Brook Hydro Plant Refurbishment. Table of Contents. 1.0 Introduction Background Electrical Works...7 Table of Contents Page 1.0 Introduction...1 2.0 Background...2 3.0 Civil Works...3 3.1 Penstock...3 3.1.1 Optimum Penstock Diameter...4 3.1.2 Penstock Replacement Options...4 3.2 Surge Tank...5 3.3 Civil

More information

THE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE

THE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE THE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE Apogee is the intermediate sailplane designed to be competitive in AMA duration contests. Effective spoilers, rudder and full flying stabilizer

More information

A Final Report to. The New Hampshire Estuaries Project. Submitted by

A Final Report to. The New Hampshire Estuaries Project. Submitted by OYSTER (CRASSOSTREA VIRGINICA) REEF MAPPING IN THE GREAT BAY ESTUARY, NEW HAMPSHIRE - 2003 A Final Report to The New Hampshire Estuaries Project Submitted by Raymond E. Grizzle and Melissa Brodeur University

More information

CRYSTEEL S. this manual must be included with the vehicle after completing the installation.

CRYSTEEL S. this manual must be included with the vehicle after completing the installation. Website: www.tbei.com E-mail: sales@tbei.com CRYSTEEL S Grain Tipper mounting and operating instructions this manual must be included with the vehicle after completing the installation. Web Site E-Mail

More information

SECTION ROOF ACCESSORIES. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION ROOF ACCESSORIES. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 07720 ROOF ACCESSORIES PART 1 GENERAL 1.1 SECTION INCLUDES Display hidden notes to specifier. (Don't know how? Click Here) A. Attachment clamp system for standing seam metal roofs. B. Attachment

More information

Sa Sass. (12) Patent Application Publication (10) Pub. No.: US 2017/ A1. (19) United States. (43) Pub. Date: Apr. 27, PACK et al.

Sa Sass. (12) Patent Application Publication (10) Pub. No.: US 2017/ A1. (19) United States. (43) Pub. Date: Apr. 27, PACK et al. (19) United States US 201701 12163A1 (12) Patent Application Publication (10) Pub. No.: US 2017/0112163 A1 PACK et al. (43) Pub. Date: Apr. 27, 2017 (54) STAMP PLATE WITH MOULDING STOP (71) Applicant:

More information

PRECAST CONCRETE STRUCTURES

PRECAST CONCRETE STRUCTURES PRECAST CONCRETE STRUCTURES 1. INTRODUCTION The concept of precast (also known as prefabricated ) construction includes those buildings, where the majority of structural components are standardized and

More information

37.5 M6. If the basin chain hole is not used, please cover it with the screw and nut supplied.

37.5 M6. If the basin chain hole is not used, please cover it with the screw and nut supplied. BASIN WASTE FLIP TOP SLOTTED CHROME 20003000018 WASTE SHELL SILICONE WASHER BASIN When fitting the waste, ensure the slotted side faces the overflow channel. SILICONE WASHER * FIXING NUT (OPTION 1) 37.5

More information

General Layout. Eng. Maha Moddather

General Layout. Eng. Maha Moddather General Layout Eng. Maha Moddather mahamoddather@eng.cu.edu.eg Introduction Concrete Beam subjected to Bending Moment around Major Axis M x Compression d Concrete tensile strength is neglected A S Tension

More information

Ornamental Fencing Pictures & Information

Ornamental Fencing Pictures & Information Ornamental Fencing Pictures & Information At Leading Edge Fences, we specialize in the installation of all types of ornamental iron and offer a wide range of styles to suit all your needs. We recommend

More information

2. All work and materials shall be in full accordance with Local and State ordinance and with any prevailing rules and regulations.

2. All work and materials shall be in full accordance with Local and State ordinance and with any prevailing rules and regulations. General Conditions: 1. Deliver all food service equipment as specified herein, including that which is reasonably inferred, with all related items necessary to complete work shown on contract drawings

More information

Please Do Not Return This Product To The Store!

Please Do Not Return This Product To The Store! MODEL NOS. T8512 TOURNAMENT SERIES 3 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts

More information

RlGIDITY AND STRENGTH OF WALL FRAMES BRACED WlTH METAL STRAPPING

RlGIDITY AND STRENGTH OF WALL FRAMES BRACED WlTH METAL STRAPPING RlGIDITY AND STRENGTH OF WALL FRAMES BRACED WlTH METAL STRAPPING information Reviewed and Reaffirmed March 1955 No. R1603 UNITED STATES DEPARTMENT OF AGRICULTURE FOREST SERVICE FOREST PRODUCTS LABORATORY

More information

PANEL CRIB PIERS AND TOWERS

PANEL CRIB PIERS AND TOWERS CHAPTER 17 PANEL CRIB PIERS AND TOWERS Panel crib piers are made of trusses with panels set horizontally or vertically and are normally braced with transoms, sway bracing, rakers, bracing frames, and tie

More information

Monitoring DC Decoupling Devices at Isolation Flanges for Compliance and Pipeline Integrity

Monitoring DC Decoupling Devices at Isolation Flanges for Compliance and Pipeline Integrity Monitoring DC Decoupling Devices at Isolation Flanges for Compliance and Pipeline Integrity Jamey Hilleary Director of M2M Products Elecsys Corporation Jerry Dewitt Senior Cathodic Protection Specialist

More information

Baker River Project License Implementation. Cultural Resource Advisory Group. FINAL Meeting Notes

Baker River Project License Implementation. Cultural Resource Advisory Group. FINAL Meeting Notes Baker River Project License Implementation Meeting FINAL Meeting Notes Team Leader: Elizabeth Dubreuil (PSE), (425) 462-3609, elizabeth.dubreuil@pse.com. PRESENT Elizabeth Dubreuil, Cary Feldmann, Mark

More information

This specification describes the minimum requirements for structural steel drawings.

This specification describes the minimum requirements for structural steel drawings. 1/7 1.0 PURPOSE This specification describes the minimum requirements for structural steel drawings. 2.0 GENERAL As stated in specification SPEC-0800, drawings are intended to be Design drawings. Sufficient

More information

Choosing, Designing, & Building a Hydraulic Log/wood Splitter

Choosing, Designing, & Building a Hydraulic Log/wood Splitter Choosing, Designing, & Building a Hydraulic Log/wood Splitter Part 1 - "Deciding on what type of log/wood splitter will best fit your needs" - Covers 4 common styles of hydraulic log/wood splitter & pros/cons

More information

Produced by the Construction Resource & Development Centre. Reprinted by the Construction Industry Council

Produced by the Construction Resource & Development Centre. Reprinted by the Construction Industry Council Produced by the Construction Resource & Development Centre. Reprinted by the Construction Industry Council Over the past 15 years the frequency and intensity of hurricanes impacting Jamaica has increased

More information

Installation Instructions for Lambo Door Mechanism. 1. Lift the hood and remove left and right shield of front wheel.

Installation Instructions for Lambo Door Mechanism. 1. Lift the hood and remove left and right shield of front wheel. Installation Instructions for Lambo Door Mechanism 1. Lift the hood and remove left and right shield of front wheel. 2. With the door open pull out the rubber hose connecting the door and the door frame,

More information

Taylor County July 2011 SECTION SHOP DRAWINGS, WORKING DRAWINGS AND SAMPLES

Taylor County July 2011 SECTION SHOP DRAWINGS, WORKING DRAWINGS AND SAMPLES SECTION 01340 SHOP DRAWINGS, WORKING DRAWINGS AND SAMPLES PART 1 - GENERAL 1.1 REQUIREMENTS INCLUDED A. Contractor shall submit to the Architect/Engineer for review and exception, if any, such working

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

SECTION INTERIOR SIGNAGE

SECTION INTERIOR SIGNAGE SECTION 10 14 02 INTERIOR SIGNAGE PART 1 GENERAL 1.1 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred to in the text by

More information

YES 45 TU Thermal Storefront System Installation Manual

YES 45 TU Thermal Storefront System Installation Manual Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION Framing

More information

INSTALLATION GUIDE PermaTrak. Patented Product: U.S. Patent #5,906,084 #8,302,362 #8,522,505 #8,839,588 #9,096,975

INSTALLATION GUIDE PermaTrak. Patented Product: U.S. Patent #5,906,084 #8,302,362 #8,522,505 #8,839,588 #9,096,975 INSTALLATION GUIDE 2009-2017 PermaTrak. Patented Product: U.S. Patent #5,906,084 #8,302,362 #8,522,505 #8,839,588 #9,096,975 Table of Contents Project Overview Forward, Acceptability Criteria, Safety,

More information

THE SIX SIMPLE MACHINES

THE SIX SIMPLE MACHINES Simple Machines A machine is a device that helps make work easier to perform. (Remember, Work = Force X Distance). A machine makes work easier to perform by accomplishing one or more of the following functions:

More information

Kelly Alexander Rolling Ball Kinetic Sculpture Summary

Kelly Alexander Rolling Ball Kinetic Sculpture Summary Kelly Alexander Rolling Ball Kinetic Sculpture Summary This design was prompted by a request to create a model exhibiting the capabilities of the selective laser sintering process. It was completed as

More information

Hip Roof Canopy Instructions

Hip Roof Canopy Instructions Hip Roof Canopy Instructions - PUT SAFETY FIRST. NOT COMPLYING WITH THE PROCEDURES AND PRECAUTIONS OUTLINED IN THIS MANUAL MAY RESULT IN PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.. Before attempting

More information

Rugged Powerful Durable

Rugged Powerful Durable Professional Grade Wood Splitters Rugged Powerful Durable Made in the USA UP TO 48 Mighty Profitable Splitters IDEAL FOR LANDSCAPE MAINTENANCE AND RENTAL Mighty Ox splitters are compact, powerful and

More information

More Storage Space Under Yacht Bed

More Storage Space Under Yacht Bed More Storage Space Under Yacht Bed Open up storage space under your bed! Convert your bed deck to a Lifting Hatch with Gas Spring assist! Many bed decks on boats and RV s have two or three pieces of plywood

More information

8-Ton Manual Splitter OWNER S MANUAL

8-Ton Manual Splitter OWNER S MANUAL 8-Ton Manual Splitter OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions

More information

HC Precast System ( 100 % Malaysia Technology With 6 IPs )

HC Precast System ( 100 % Malaysia Technology With 6 IPs ) Choose Industrialised Building System ( IBS ) for Economical Construction Industrialised Building System ( IBS ) functions as a comprehensive superstructure construction system whereby flexibility in it's

More information

CONSTRUCTION SPECIFICATION FOR MAINTENANCE HOLE, CATCH BASIN, DITCH INLET, AND VALVE CHAMBER INSTALLATION

CONSTRUCTION SPECIFICATION FOR MAINTENANCE HOLE, CATCH BASIN, DITCH INLET, AND VALVE CHAMBER INSTALLATION ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 407 NOVEMBER 2013 CONSTRUCTION SPECIFICATION FOR MAINTENANCE HOLE, CATCH BASIN, DITCH INLET, AND VALVE CHAMBER INSTALLATION TABLE OF CONTENTS 407.01

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL FASTENER AND HARDWARE GENERAL REQUIREMENTS 1. DESCRIPTION This section contains general requirements for common hardware installation. Covered are selection and installation of cotter pins, installation

More information

Jeep Cherokee Door XJ Set Part # Revision J

Jeep Cherokee Door XJ Set Part # Revision J Jeep Cherokee 84-96 4 Door XJ Set Part # 10911 Revision J 6-5-06 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure

More information

INVICTA PENSTOCK SOLUTIONS PENSTOCK SOLUTIONS

INVICTA PENSTOCK SOLUTIONS PENSTOCK SOLUTIONS INVICTA PENSTOCK SOLUTIONS PENSTOCK SOLUTIONS INVICTA PENSTOCK RANGE Invicta is a well established, service driven company offering complete valve, penstock and actuator solutions. Invicta Valves was formed

More information

ACORNWIRE.COM MESH PARTITIONS DIVISION 10 - SPECIALTIES WIRE MESH PARTITION FOLDING GATE

ACORNWIRE.COM MESH PARTITIONS DIVISION 10 - SPECIALTIES WIRE MESH PARTITION FOLDING GATE acorn WIRE ACORNWIRE.COM MESH PARTITIONS DIVISION 10 - SPECIALTIES 10 22 13 WIRE MESH PARTITION 10 22 16 FOLDING GATE GUIDE Page 4 / 5 No. 130A All wire type for normal industrial use. 7, 8, 9, 10 and

More information

SPECIALISED INFRASTRUCTURE

SPECIALISED INFRASTRUCTURE S I STOPBOARDS I BULKHEADS I FLOODGATES SPECIALISED WAT E R C O N T R O L INFRASTRUCTURE Operating on a worldwide scale, AWMA service all industries with engineered, purpose built, water control equipment

More information

Memorandum. Application for Amendment to DNR Land Use Permit # LAS29209

Memorandum. Application for Amendment to DNR Land Use Permit # LAS29209 Memorandum Date: September 12, 2013 Project Number: 1992.06k To: From: Subject: cc: Jessica Meybin (ADNR) Tim Sullivan (R2) Application for Amendment to DNR Land Use Permit # LAS29209 Kevin Petrone and

More information

AVK PENSTOCK SOLUTIONS PENSTOCK SOLUTIONS

AVK PENSTOCK SOLUTIONS PENSTOCK SOLUTIONS AVK PENSTOCK SOLUTIONS PENSTOCK SOLUTIONS AVK PENSTOCK RANGE AVK UK is part of the globally renowned AVK group who are based in over 85 countries and are known as one of the leading innovators and manufacturers

More information

Crimp Type Winding Connections in Hermetic Motors

Crimp Type Winding Connections in Hermetic Motors Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 1974 Crimp Type Winding Connections in Hermetic Motors G. W. Klein General Electric Company

More information

FROM THE P.E.I. GROUP

FROM THE P.E.I. GROUP 1 FROM THE P.E.I. GROUP PROTECTIVE SHIELDS WITH THE NEW STEEL BAND COVER 2 J & JL ROLL-UP COVER 3 4 BIPLASTIC WIPER ROUND AND SHAPED HEAT- WELDED BELLOWS AT THE 26 th BI-MU 2008 1) PROTECTIVE SHIELDS WITH

More information

B422 - PRECAST REINFORCED CONCRETE BOX CULVERTS AND BOX SEWERS - OPSS 422

B422 - PRECAST REINFORCED CONCRETE BOX CULVERTS AND BOX SEWERS - OPSS 422 B422 - PRECAST REINFORCED CONCRETE BOX CULVERTS AND BOX SEWERS - OPSS 422 422.1 GENERAL The work under these tender items consists of the fabrication and installation in open cut of precast reinforced

More information

PORTABLE BULLET TRAP ASSEMBLY & OPERATION/MAINTENANCE MANUAL REVISION 2.0. ACTION TARGET 3411 Mountain Vista Pkwy Provo, UT 84606, USA

PORTABLE BULLET TRAP ASSEMBLY & OPERATION/MAINTENANCE MANUAL REVISION 2.0. ACTION TARGET 3411 Mountain Vista Pkwy Provo, UT 84606, USA PORTABLE BULLET TRAP ASSEMBLY & OPERATION/MAINTENANCE MANUAL REVISION 2.0 ACTION TARGET 3411 Mountain Vista Pkwy Provo, UT 84606, USA PORTABLE BULLET TRAP ASSEMBLY & OPERATION/MAINTENANCE MANUAL COPYRIGHT

More information

SLIDE GATE SERVICE CONDITIONS

SLIDE GATE SERVICE CONDITIONS SLIDE GATE The model is a 4 side sealing slide gate designed for wall mounting. It is used mainly in water treatment, irrigation, hydraulic works and hydroelectric power plants. There are two different

More information

Method of Build 1. Fire. Sound

Method of Build 1. Fire. Sound Method of Build 1 General Viso Fire & Acoustic in the solid form differs from most other systems as it can be erected using 12.5mm & 15.0mm boards within the same Aluminium framework. Also hidden fix board

More information

Progress Report 2 Document

Progress Report 2 Document Solar Tracking Structure Design By: Joshua Belsheim, Travis Francis, Jiayang He, Pengyan Liu, Anthony Moehling, and Micah Ziemkowski Team 07 Progress Report 2 Document Submitted towards partial fulfillment

More information

INSTALLATION INSTRUCTION FOR WOOD DOUBLE-HUNG AND CASEMENT WINDOWS USING WOOD BRICKMOULD OR FLAT CASING

INSTALLATION INSTRUCTION FOR WOOD DOUBLE-HUNG AND CASEMENT WINDOWS USING WOOD BRICKMOULD OR FLAT CASING 2009 Pella Corporation Part Number: 80DZ0101 INSTALLATION INSTRUCTION FOR WOOD DOUBLE-HUNG AND CASEMENT WINDOWS USING WOOD BRICKMOULD OR FLAT CASING Brickmould/Flat Casing Aluminum Head Flashing Corner

More information

General Guidelines:

General Guidelines: ASSEMBLY INSTRUCTIONS Congratulations on your new Patriot Dock purchase. This manual contains instructions to assemble basic dock configurations for use at typical residential shoreline application. Please

More information

SERIES 5001 SLIDING GLASS DOOR PATIO DOORS INSTALLATION GUIDE

SERIES 5001 SLIDING GLASS DOOR PATIO DOORS INSTALLATION GUIDE PATIO DOORS INSTALLATION GUIDE These instructions cover general installation conditions. Improper installation could affect your doors operation and warranty. Deviations from these instructions should

More information

CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST

CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO. 2012-16A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST 2014 CHAIN LINK FENCE SPECIFICATIONS Chain link fence,

More information

Precast Concrete Panels for Rapid Pavement Repair

Precast Concrete Panels for Rapid Pavement Repair Precast Concrete Panels for Rapid Pavement Repair Scott Shuler, Ph. D., P. E. Colorado State University Ft. Collins, CO 80523-1584 Gary Dewitt, P. E. Colorado Department of Transportation Evans, Colorado

More information

Pendulum drilling Pendulum drilling for monitoring the Emosson dam

Pendulum drilling Pendulum drilling for monitoring the Emosson dam 2015 Pendulum drilling Pendulum drilling for monitoring the Emosson dam Diamantbohr Gruppe Bolimattstrasse 7, 5033 Buchs Verfasser: B.Steiner/Ph.Wingeier Photograph: Satellite image of Lac d`emosson Source:

More information

SHED-5932-F, MANUAL.doc

SHED-5932-F, MANUAL.doc VESTIL MANUFACTURING CORP. 2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868 Fax: (260) 665-1339 www.vestilmfg.com e-mail: HUsales@vestil.comU

More information

Chapter 17. Forcible Entry

Chapter 17. Forcible Entry Chapter 17 Forcible Entry Introduction 2 ½ million homes broken into each year Owners install a variety of locking devices to protect both homes and businesses Forcible entry often one of the first operations

More information

Well Casing Cathodic Protection - Design Issues, Lessons Learned and a Case History

Well Casing Cathodic Protection - Design Issues, Lessons Learned and a Case History Well Casing Cathodic Protection - Design Issues, Lessons Learned and a Case History Jeffrey L. Didas Matcor, Inc. 101 Liberty Lane Chalfont, PA 19111 USA WRGC Western Regional Gas Conference 2018 Henderson,

More information